DSC GS3060 Installation Manual Download Page 13

9

Yellow Light 

Status

What It Means: GSM Status/Communication Indicator

Yellow Light

ON

• When used as the primary communicator, the yellow light will always be

ON.

• When used as a backup communicator, the yellow light will be ON when

there is a no phone line connected to the GS3060 TIP and RING, or the line
voltage goes below 2.8VDC.

Yellow Light

OFF

• Indicates a good phone line is connected to the GS3060. (more than 2.8

VDC detected across the GS3060 TIP and RING terminals).

Yellow Light

FLASHING

• The yellow light will flash one time when the GS3060 transmits a signal

and two times when a kisoff is received.

Red Light 

Status

What it means:

Trouble Status 

Trouble Status - Troubleshooting Steps

One Flash

GS3060 Low Battery

• Measure the battery under load and verify it is

charged to at least 12.5 VDC. If not, wait at least 1
hour for the battery to charge

• Remove the battery and measure the voltage across

the two battery leads; the voltage should be at least
13.5 VDC

• Verify the input DC supply is rated at 13.8VDC @

120mA minimum

• Ensure the GS3060 jumper J3 is OFF

Two Flashes

SIM/Radio Trouble

• Ensure the SIM Card is inserted correctly and firmly
• Ensure the antenna cable is plugged securely into the

radio connector

• Ensure the power source connected to the GS3060 is

providing 13.8VDC @ 120mA and that the battery is
fully charged

Three
Flashes

GSM Network Problem

• Ensure the SIM card has been activated
• The antenna cable should be plugged securely into

the radio connector

• Ensure there is good signal strength (at least one

green light ON)

• Verify the installation area is not experiencing a net-

work outage

Four Flashes

Insufficient Signal
Strength

• Ensure there is good signal strength (at least one

GS3060 green light ON)

• Ensure the antenna cable is plugged securely into the

radio connector

Five Flashes

Configuration Trouble

• Ensure the SIM card is activated

Six Flashes

Receiver Not Available

• Contact the monitoring station to verify that the

GS3060 programming is correct (port, IP address,
DNIS)

• Contact your central station to verify they are not

experiencing any receiver issues

Seven
Flashes

DC Supply Trouble

• Ensure the power source connected to the GS3060 is

providing 13.8VDC @ 120mA

firealarmresources.com

Summary of Contents for GS3060

























Reviews: