EN
Instructions
Customer Service / Importer:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
✆
+49 38851 314650 *)
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
All rights reserved.
Article number: 07787
Dear Customer,
We are delighted that you have chosen this
outdoor bottle cooler.
If you have any questions about the article and about spare parts /
accessories, contact the customer service department via our
website:
www.service-shopping.de
Explanation of Symbols and Signal Words
Danger symbol: This symbol indicates dangers of injury.
Read through the associated safety instructions carefully
and follow them.
Supplementary information
WARNING
warns of
possible
serious injuries and danger to
life
CAUTION
warns of slight to moderate injuries
IMPORTANT INSTRUCTIONS
■
The article is intended to be used for keeping up to 15 drink
bottles cool. However, it is not intended to be used to chill the
drinks.
■
The article is suitable for conventional 0.33 l and 0.5 l drink
bottles made of glass and plastic.
■
The maximum load it can carry is 10 kg.
■
The article is designed for personal use only and is not
intended for commercial applications.
■
The article should only be used as described in these instruc-
tions. Any other use is deemed to be improper.
■
WARNING – Risk of injury and suffocation!
Keep children
and animals away from the article and packaging material.
■
The article is
not
a toy!
■
CAUTION – Danger of injury!
–
Never place the frame down on the guide ring! It could topple
over and the bottles could be broken.
–
Never leave the housing open. It must not present a trip
hazard!
■
Leave a suf
fi
cient amount of clear space around the hole in the
ground (min. 50 cm).
■
Clean the article with a damp cloth and mild cleaning agent
if necessary. Do not use any corrosive or abrasive cleaning
agents! These could damage the surface.
Items Supplied and Article Overview
1
Handle
2
Tray for 5 bottles
(3 x)
3
Rod (3-piece)
4
Guide ring
5
Housing (3-piece)
6
Lid (insulated)
3
5
3
1
2
4
6
Before Initial Use
• Unpack all parts and remove any protective
fi
lms or stickers.
Check the items supplied for possible transport damage. If you
should
fi
nd any transport damage, do not (!) use the article, but
contact the customer service department immediately.
• Assemble the article (see the “Assembly” section).
• Dig a hole in the ground (see the “Digging a Hole in the
Ground” section).
Putting Into Operation
Assembly
1. Screw the three housing parts (
5
) to one another.
2. Screw one tray (
2
) onto the bottom end of one rod part (
3
). The
recesses of the tray must be facing upwards. Repeat this step
for the other two trays.
3. Screw together the three resulting units to create a frame.
4. Screw the handle (
1
) onto the top end of the frame.
5. Plug the guide ring (
4
) into the lowest tray opening.
Digging a Hole in the Ground
PLEASE NOTE
■
Make sure that no cables are bored into or destroyed. Find out
where cables may possibly run and avoid them.
A earth auger is best suited for digging the hole in the
ground.
Make sure you follow the instructions in the
guide for the earth auger!
This is not supplied with the
article.
Tip:
A earth auger can be borrowed from most DIY
stores.
1. Dig a hole in the ground (diameter of approx. 25 cm). It must be
around 90 cm deep so that the ground is
fl
ush with the edge
of the housing (
5
).
2. Place the screwed-together housing in the hole in the ground.
3. Fill the hole in the ground around the housing with earth. Care-
fully compact it as you do so.
4. To remove the housing from the ground, spread out the hole in
the ground around the housing. It should be possible to pull the
housing out of the ground easily in one go.
Use
PLEASE NOTE
■
The maximum load capacity for the article must not be
exceeded.
1. Insert cool (!) bottles into the recesses of the trays (
2
).
2. Insert the frame containing the bottles into the housing (
5
) in
the ground.
3. Place the lid (
6
) on the housing.
4. To protect the article and its contents from direct sunlight, also
cover the lid, e. g. by placing a
fl
ower pot on top of the lid.
Article Data
Article number:
07787
Dimensions:
Height:
approx. 90 cm
Width:
approx. 22 cm
Weight:
2.3
kg
Load capacity:
max. 10 kg
Disposal
Dispose of the packaging material and the article in an en-
vironmentally friendly manner and take them to a recycling
centre.
Z 07787 M DS V3 0118
07787_DE-EN-FR-NL_A4_V3.indd 2
07787_DE-EN-FR-NL_A4_V3.indd 2
04.01.2018 14:33:44
04.01.2018 14:33:44
