background image

 

4

5. TECHNICAL SPECIFICATIONS 

 

CHARACTERISTIC 

VIP4Tools lubrication panel

 

Air supply pressure 

5 - 8 bar 

Working temperature 

-5 - +55 °C 

Working humidity 

90% max 

Permitted lubricants 

Mineral - synthetic 

Oil viscosity at working 

temperature 

32 - 320 cSt 

Conservation temperature 

-20 - +65 °C 

 

SAMBA LEVEL 

 

Temperature:  

-10°C - +80°C 

Maximum switching power: 

50W 5V 

Maximum current: 

1 A 

Maximum voltage: 

220 V ac 

 
 

WARNING:

 DO NOT supply the machine with voltages or pressures other than those indicated 

on the specification plate. 

 
 

6. HANDLING AND TRANSPORT

 

 

Prior to dispatch VIP4Tools lubrication panels are carefully packed in a cardboard carton. During 

transportation and storage maintain the equipment the right way up as indicated on the carton.  

On receipt, check that the packaging is not damaged and store the equipment in a dry place. 

 
 

7. PRECAUTIONS IN USE 

 

It is necessary to carefully read the warnings and the risks involved in using the lubrication panel. The 
operator must understand the functioning of the unit by studying  the user’s manual. 

 

Electric currents 

No intervention must be attempted on the equipment without first having disconnected the electrical 
power supply (electric level) and ensuring that it cannot be reconnected during the intervention. 
All installed equipment, electrical, electronic, tank and base structure, must be connected to the 
ground line. 

(see paragraph 10.7).

 

Flammability 

The oil employed in the lubrication circuit is not normally flammable. It is nonetheless indispensable to 
take every precaution against the oil coming into contact with very hot parts or open flames.  

Pressure 

Prior to any intervention on the equipment ensure that pressure is released from all branches of the 
lubrication circuit. Failure to do this could result in oil being discharged under pressure where 
connections or components are disassembled 

(see paragraph 10.6). 

Noise 

The VIP4Tools lubrication panel does not emit excessive noise, remaining below 70dB(A). 
 

WARNING:

 before carrying out the replacement of the mini-pumps, empty the tank of 

lubricant. 

 

 
 
 
 
 
 
 
 

Summary of Contents for VIP4Air 110 V AC

















Reviews: