background image

Maintenance and Care

English ·

   

17

 

W

 Maintenance of the battery charger

The  charging  unit  does  not  require  any  mainte-
nance.  The  housing  must  only  be  cleaned  with 
mild detergents that are free from solvents, or by 
means of a damp cloth. Make sure that no liquid 
enters  into  the  charging  unit.  Before  using  the 
charging  unit  again,  always  make  sure  that  the 
unit is completely dry. If necessary, store the unit 
in a dry, ventilated place for several hours without 
connecting it to mains power.

¢

Attention:

Before  cleaning  the  battery  charger  it  must 
be completely disconnected from the mains  
power  (always  make  sure  to  pull  the  mains 
power plug).

W

Charging the storage battery

Make sure that the battery is fully charged before 
use! The voltage rating on the charging unit has 
to be compatible with the voltage of your power 
supply. (e.g. 220V – 240V in Europe, and 110V in 
USA).

1.  Plug the jack plug of the battery charger into 

the socket on the spiral cord of the hand con-
trol until the jack plug is locked in. 

2.  Insert  the  mains  plug  of  the  battery  charger 

 into  a  socket.  The  red  control  lamp  on  the 
hand control will be light up until the battery is 
charged – after that, it will change to green.

     If  you  want  to  charge  the  battery  complete-

ly, leave it connected to the charging unit. The 
control unit of the battery charger will terminate 
the charging process after approx. 4 hours.

    This prevents that the battery from being over-

charged. 

3.  Remove  the  mains  power  plug  from  the 

 socket. 

4.  Remove  the  jack  plug  of  the  battery  charger 

from the socket on the hand control.

¢

Important information:

•  If the control lamp is not lit up after connecting 

the hand control, please check the following:

   –  

Connections

  (is  the  jack  plug  fully  plugged 

into the charging socket?)

•  Use  the  battery  charger  only  in  closed  rooms 

and  protect  it  against  water  and  humidity.

Do not use the battery charger in the bath-
room.

¢

Note:

•  If  the  battery  charger  is  damaged,  please 

 return it to the supplier for inspection.

Summary of Contents for Bellavita



























Reviews: