background image

14

ULTRA-SORB MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Mounting and support

The Ultra-sorb panel can operate with air flow in either direction. The steam 
supply and condensate drain connections must be connected to the header 
assembly. To locate connections, the panel may be rotated 180º to the 
preferred side of the AHU or duct.

Once installed, verify that all steam discharge tubelets are pointed 
perpendicular to the airstream (see Figure 14-1). Loosen the jam nut at 
the top of the tube to allow rotation of the dispersion tubes for proper tubelet 
orientation.

When removing and installing the dispersion tubes, verify that the replacement 
grommets are seated in their grooves and lubricated. When sliding the 
dispersion tube into the grommet, be careful not to cut the grommet.

Note:  To prevent leakage, use HVAC caulking, compressible strip, or a similar 

weather sealant to the dispersion panel joints and duct flanges. Seal all 
places where the Ultra-sorb installation hardware and fittings penetrate 
the wall of the duct. See Figure 14-1 below.

Airflow

Tubelet

Dispersion tube

Airflow

OM-150a

FIGURE 14-1:  
DISPERSION TUBE ORIENTATION

OM-7587_a

FIGURE 14-1: ULTRA-SORB MODEL MP IN A HORIZONTAL AIRFLOW WITH ELECTRODE-TYPE HUMIDIFIER

Sealant 

at joints

Sealant 

at joints

Use compressible 

strips to seal the 

flanges to the duct 

flange

Summary of Contents for MP

































Reviews: