Drill Master 69947 Owner'S Manual Download

Page: 14 / 16

Page 14

For technical questions, please call 1-800-444-3353.

Item 69947

SAFET

Op
ERA
TION

AINTENAN

SETU
p

parts List and Diagram

pLEASE READ THE FOLLOWING cAREFULLy

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE

BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR

THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE

MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,

AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,

OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

parts List

Record product’s Serial Number Here:
Note:

If product has no serial number, record month and year of purchase instead.

Note:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

part

Description

Screw

Chuck

Spindle

Ball

Spring

Needle Bearing

Retaining Ring

Gear

Arm

Function Switch

Gearbox

Ball Bearing (608)

part

Description

Brush Holder

Carbon Brush

Brush Cap

Right Housing

Screw

Inductor

Ball

Retaining Ring

Needle Bearing

Rotor

Ball Bearing (626)

Stator

part

Description

Left Housing

Cord Clip

Screw

Trigger

Capacitor

Cord Protector

Cord

Depth Gauge

Side Handle

Chuck Key

Summary of Contents for 69947

















Search results

Summary of Contents for 69947

Reviews:

Related manuals for 69947

Brands by name

Popular brands

Drill Master 69947, Owner'S Manual

Search results

Summary of Contents for 69947

Reviews:

Related manuals for 69947

Brands by name

Popular brands