background image

User Manual 

BULIT 

– IN GAS STOVE | 

LIVORNO 76 

Professionale

 

 

 

 

15 

9. PROBLEM SOLVING 

• 

Repairs should only be performed by an authorized technician. Improper repair can be dangerous for 

you and other important people. 

• However, some minor problems can be solved as follows: 

Issue 

Probable cause 

Solution 

It does not turn on 

No spark 

Check power supply 

The 

burner 

cover 

is 

improperly 

mounted 

Mount the cover correctly. 

The gas supply is closed. 

Open the gas supply complete 

Poorly lit 

The gas supply is not completely open. 

Open the supply gas 

The burner cover is not properly mounted. 

Replace the cover correctly. 

The spark plug is contaminated with the foreign 
substance. 

Clean the foreign substance with a dry cloth. 

The burner is wet. 

Thoroughly dry burner cap 

The holes in the flame diffuser are clogged. 

Clean the flame diffuser. 

Produces  noises  when 
you turn on 

Burner cover is wrong mounted 

Mount the burner cap correctly. 

Flame  shuts  off  when  in 
use. 

Flame Control has foreign substances. 

Clean the device. 

The  food  being  cooked  overflowed  and 
extinguished the flame. 

Turn off the burner. Wait a minute and turn it 
on again. 

 

A strong current turns off the burner. 

Turn  off  the  burner  and  check  the  kitchen 
area, such  as  open  windows.  Wait a  minute 
and turn it on again. 

Yellow flame 

The holes in the flame diffuser are clogged. 

Clean the flame diffuser. 

Different gas issued. 

Check the gas used. 

Unstable flame 

The burner cover is not properly mounted. 

Mount burner cap correctly 

Smell of Gas 

Gas leak 

Do  not  use  the  stop,  close  the  gas  valve. 
Open  the  window  to  ventilate.  Contac  tour 
Service Center from outside. 

 The problem is not resolved, contact the service center.

 

Summary of Contents for LIVORNO 76 Professional

















Reviews: