DrBrowns AC178-INTL, Instructions For Use Manual

Page: 9 / 40

7
2 f ilters are included�
To purchase replacement filters, contact your local distributor�
WARRANTY
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase� Any defective part will be repaired or replaced at no
charge if it has not been tampered with and appliance has been used according to these
printed instructions� This warranty gives you specific legal rights as well as other rights
which vary from state to state�
This warranty does not cover a defect that has been caused by negligence, accidents or
improper use of the appliance� To keep your Dr� Brown’s™ Bottle Sterilizer and Dryer in
good condition and retain your warranty, USE ONLY AS DIRECTED�
CUSTOMER SERVICE
If you experience unsatisfactory operation or have questions/comments, please contact
your local Dr� Brown’s distributor� See drbrownsbaby�com/distributors to find your local
contact�
REPLACING THE FILTER
CAUTION:
Unplug from outlet and allow to cool for 60 minutes before
replacing filter�
Replace the filter every six months of regular use for optimal performance�
Follow the steps below:
1� The filter is located at the bottom of the base� Gently squeeze the latches on the filter
cover to remove it�
2� Remove and replace the filter, ensuring the pull tab is still visible on top of the filter�
3� Snap the filter cover back into position�
Note:
Filter must always be used to ensure proper performance�
4
A
1 2 3
D
C
B
2 1 4 3
C
B
A
D
MATERIAL
FILTER REPLACEMENT
DO NOT SCALE DRAWING
SHEET 1 OF 1 SCALE: 1:1
REV. DWG. NO. C SIZE
TITLE:
DRAWN DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
SOLIDWORKS
MFG/Q.A APPR.
ENG APPR.
THIS DRAWING AND RELATED 3D CAD DATA
CONTAINS PROPRIETARY INFORMATION
THAT ARE THE PROPERTY OF
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
X
.X
.XX
.XXX
X
.X
2.5
0.5
0.25
0.13
0.5
0.25
NO PLACE:
ONE PLACE:
TWO PLACE:
THREE PLACE:
ANGLE:
ANGLE:
INTERPET PER ASME Y14.5-1994
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
3D
HANDI-CRAFT COMPANY
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
THIRD ANGLE
PROJECTION
1
15JUL19 RBW
2 1
A
B
A
B
1 2
1
THIRD ANGLE
PROJECTION
HANDI-CRAFT COMPANY
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
3D
INTERPET PER ASME Y14.5-1994
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
NO PLACE:
ONE PLACE:
TWO PLACE:
THREE PLACE:
ANGLE:
ANGLE:
2.5
0.5
0.25
0.13
0.5
0.25
X
.X
.XX
.XXX
X
.X
THIS DRAWING AND RELATED 3D CAD DATA
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE PERMISSION
OF HANDI-CRAFT CO.
ENG APPR.
MFG/Q.A APPR. SOLIDWORKS
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
DRAWN
TITLE:
SIZE
A
DWG. NO. REV.
SCALE: 1:2
RBW
15JUL19
SHEET 1 OF 1 DO NOT SCALE DRAWING
FILTER AND COVER
MATERIAL
1
3
2