background image

- 3 -

 

 

CAREFULLY READ THIS MANUAL BEFORE INSTALLING THE WATER HEATER! 

 
Dear Customer, 
 
The Works Cooperative of Dražice - Machine Plant, Ltd., would like 
to  thank  you  for  your  decision  to  use  a  product  of  our  brand. 
With  this  guide,  we  will  introduce  you  to  the  use,  construction, 
maintenance and other information on electrical water heaters. 
 
The product is not intended to be controlled by 

a)

 

people (including children) with reduced physical, sensual or mental capacities, or 

b)

 

people  with  insufficient  knowledge  and  experiences  unless  supervised  by  responsible  person, 
or unless properly instructed by such responsible person. 

 
The manufacturer reserves the right for engineering modification of the product. The product is designed 
for permanent contact with drinkable water. 
 
It is recommended to use the product in indoor environment with air temperatures from +2°C to +45°C 
and a relative humidity up to 80%. 
 
Product’s reliability and safety is proven by tests implemented by the Engineering Test Institute in Brno. 
 
Made in the Czech Republic. 
 
 
 
 

Meaning of pictograms used in the Manual 

 
 
Important information for heater users. 
 
 
 
Abiding by the recommendations of the manufacturer serves to ensure trouble-free operation 
and the long service life of the product. 
 
 
 
Caution!  
Important notice to be observed. 

 

 

Summary of Contents for OKC 400 NTRR/HP/SOL














Reviews: