5
Programmers allow you to set ‘On’ and ‘Off’ time periods.
Some models switch the central heating and domestic hot
water on and off at the same time, while others allow the
domestic hot water and heating to come on and go off at
different times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle.
On some programmers you must also set whether you want
the heating and hot water to run continuously, run under the
chosen ‘On’ and ‘Off’ heating periods, or be permanently off.
The time on the programmer must be correct. Some types
have to be adjusted in spring and autumn at the changes
between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating pro-
gramme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These
are explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched
the heating off. And, if you have a hot-water cylinder, the
water heating will not work if the cylinder thermostat detects
that the hot water has reached the correct temperature.
INSTALLATION MUST ONLY BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN OR
HEATING ENGINEER.
MAKE SURE MAINS INPUT HAS A 3 AMP FUSE.
Lifestyle Programmers and Timeswitches conform to the
essential requirements of these Directives:
2 (1) A 230V a.c. each switch
Display: blank
Time: always kept
Program times: always preserved
Fixed wiring only, to comply with
current IEE regulations
Must be maintained by a qualified
electrician or heating engineer
Drayton
Tempus 6, 7
N
L 1
2
3
4
Drayton Lifestyle
LP112, LP241, LP522, LP722
N
L 1
2
3
4
Switchmaster
400, 600
N
L
4
3
1
(no connection to terminal 4 on 600)
Switchmaster
805, 900, 900i
N
L 4
2
3
1
ACL
MP (Towerchron)
2
1
ACL
FP (Towerchron)
2
1 8 11
6 10
Tempus 3, 4, 6, 7 (old models),
Danfoss Randall
CP15, CP715, FP15, FP715 (Mk18)
E
N
L 1
2
3
4
Danfoss Randall
3020P, 3060
E
7
6
4
2
Danfoss Randall
4033 (link 1-6)
E
7
6 5
3
4
2
Danfoss Randall
102, 102E, 102E5, 102E7 (link 6-3)
E
5
6
1
2
Danfoss Randall
701 (link L-5 and 5-6)
E
N
L
3
1
Danfoss Randall
702 (link L-5 and 5-6)
E
N
L 4
2
3
1
Danfoss Randall
922, 972 (link L-2 and 2-5)
E
N
L 1
4
3
6
Danfoss Randall
SET2, SET2E, SET3E, SET3M, FP975 E
N
L 3
6
1
4
SET5 (link L-2 and 2-5)
Grasslin Towerchron
DP 72, QE2
N
L 1
2
3
4
Honeywell
ST 699/799 (link L-5 and 5-8)
N
L 7
4
6
3
Honeywell
ST 6200, ST 6300, ST 6400, ST 6450
N
L 1
2
3
4
Honeywell
ST 7100 (link L-3 and 3-6)
N
L 7
4
8
5
Horstmann
525, 527, 425 Diadem, H21, H27,
E
N
L 3
6
1
4
H121, Tiara (link L-2 and 2-5)
Landis & Staefa*
RWB2, RWB2E, 20, 40, 102, 200,
N
L 1
2
3
4
252 & 270, RWB9
Myson
Microtimer (link L-5 and 5-8)
N
L 7
4
6
3
Potterton Myson
All EP2000’s, EP3000’s, EP6000’s
N
L 1
2
3
4
(link L-5 and N-N)
Potterton Myson*
Mini Minder
N
L 1
2
3
4
Sunvic
Select 207, SunPro 2000
N
L 1
2
3
4
Sunvic
SP50, SP100 (link L-3)
N
L 1
4
2
5
Sunvic
SP20, SP35
N
L
3
5
4
5
Venner
Vennerette
N
L
LINE
LOAD
User’s Instructions
The programmer must be set to the type of system it is to con-
trol. The link on the back of the unit has two settings – P and G.
P = a fully pumped and controlled system – allowing
heating and hot water to be set separately.
G = a gravity-fed hot water system – which does not allow
independent setting of heating without hot water, though
hot water can be controlled alone.
PROGRAMMER TERMINAL COMPARISONS
Current Models
Earth
Neutral
Live
Ch1 on
Chl2 on
Ch3 on
Ch4 on
MAKE
MODEL
Discontinued/Competitors’ Models
* Can simply be removed from the backplate and replaced without any disturbance to the existing wiring.
WIRING THE TIMESWITCH
Make the wiring connections as
above. Note that the output
contacts are voltage-free, so
power needs to be put on to
Terminal 1 either by linking from
Terminal L or from a separate
supply with a
INTRODUCTION
Lifestyle Timeswitches will automatically control your system
by switching it on and off at times that suit you. The light on the
front of the timeswitch shows when it’s on.
LP111Si – a 24hr program, up to 3 heating periods
each day, and every day the same.
LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
If the engineer hasn’t set your timings for you, your timeswitch
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply turn to
the page for your timeswitch model.
Sangamo
M5 (link 1-6)
N
L
1
8
N
L 1
2
3
4
Salus
EP200, SP220
Myson
MEP2C
N
L 1
2
3
4
Drayton
Drayton
Drayton
British Gas
SM2
miGenie Wish 2
MiTime MT721R, MiTimeRF Pack 2 & 3
EMP2, UP1, UP2
N
L 1
2
3
4
N
L 1
2
3
4
N
L 1
2
3
4
N
L 1
2
3
4
