Installation Guide
D2RF
Option 02 - Freeze Protection
Freeze protection will switch on the heating if the room
temperature falls to 5°C and will then control the
temperature at 7°C even if the Digistat is in OFF mode.
The Freeze Protection default is ON.
To switch off the Freeze Protection mode enter the
Installer Options Menu (Refer to Installer Options 02)
and change to OFF.
Press
to accept.
Option 04 & 05 - Low and High Limit
set points.
The user temperature set points defaults are High 32°C
and Low 5°C, to change these limits enter the Installer
Options Menu (Refer to Installer Options 04 & 05).
Option 06 - Intelligent Delayed Start
(Energy saving feature).
The Intelligent Delayed Start is an energy saving feature
which automatically reduces the warm up time for the
heating system.
If you wish to change any of the Installer Options as
shown in the table below, enter the Installer Option
Menu from Auto mode by pressing:
and +
simultaneously for 5 seconds.
Pressing
and + again for 5 seconds will exit the
Menu and return to Auto mode.
Once the Installer Options screen has been selected,
the
and
buttons allow you to scroll
through the Menu
(shown below).
The + and - allow you
to change values.
Once a value has been changed
pressing
before
exiting the Menu will save the new setting.
(The below
display shows Option 02 OFF).
Installer Options
Installer
Options
Function Select
Option
Default
02
Freeze
protection
On
Off
On
04
Low Set
Point °C
5
High
Limit
5
05
High Set
Point °C
Low
Limit
32
32
06
Delayed
Start
(Energy
saving
feature)
On
Off
Off
10
Valve
protection
On
Off
Off
11
Valve
protection
time (Mins)
1
5
3
12
Application
type
0
1
0
13
System
Capability
0
1
0
Drayton
Di2RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: [email protected]
User Guide 06490097001 IssA
Programmable Room
Thermostat Wireless
24 Hour
Model: RF700/22090
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Di2RF thermostat is a programmable thermostat 24-Hour
product (the same program for every day of the week) which
allows you to set up to 6 time and temperature events per day.
Clock Setting
Your Di2RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Di2RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
The Di2RF thermostat is a programmable thermostat
24-Hour (the same program for every day of the week) and
allows you to set 6 time and temperature events per day.
Di2RF
Pre-set Program
Your Di2RF comes with the following default settings
pre-programmed for your convenience:
Pre-set Program 1. (9 til 5)
*The above settings can be understood using the chart below
1
2
3
4
5
6
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period
Room
Temp
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
To adjust these times and temperatures
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Basic Settings
Your Di2RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1)
(Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Di2RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Di2RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Di2RF
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Once the time has been set
press
to confirm and
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Certification Mark
Drayto n
Digist at +2RF
Digist at +2RF
Digist at +2RF
Digist at +2RF
Drayto n
Drayto n
Drayto n
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
06490097001 IssA 24-1-07 13/2/07 11:59 Page 1
Drayton
Di2RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: [email protected]
User Guide 06490097001 IssA
Programmable Room
Thermostat Wireless
24 Hour
Model: RF700/22090
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Di2RF thermostat is a programmable thermostat 24-Hour
product (the same program for every day of the week) which
allows you to set up to 6 time and temperature events per day.
Clock Setting
Your Di2RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Di2RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
The Di2RF thermostat is a programmable thermostat
24-Hour (the same program for every day of the week) and
allows you to set 6 time and temperature events per day.
Di2RF
Pre-set Program
Your Di2RF comes with the following default settings
pre-programmed for your convenience:
Pre-set Program 1. (9 til 5)
*The above settings can be understood using the chart below
1
2
3
4
5
6
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period
Room
Temp
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
To adjust these times and temperatures
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Basic Settings
Your Di2RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1)
(Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Di2RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Di2RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Di2RF
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Once the time has been set
press
to confirm and
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Certification Mark
Drayto n
Digist at +2RF
Digist at +2RF
Digist at +2RF
Digist at +2RF
Drayto n
Drayto n
Drayto n
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
06490097001 IssA 24-1-07 13/2/07 11:59 Page 1
Drayton
Di2RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: [email protected]
User Guide 06490097001 IssA
Programmable Room
Thermostat Wireless
24 Hour
Model: RF700/22090
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Di2RF thermostat is a programmable thermostat 24-Hour
product (the same program for every day of the week) which
allows you to set up to 6 time and temperature events per day.
Clock Setting
Your Di2RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Di2RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
The Di2RF thermostat is a programmable thermostat
24-Hour (the same program for every day of the week) and
allows you to set 6 time and temperature events per day.
Di2RF
Pre-set Program
Your Di2RF comes with the following default settings
pre-programmed for your convenience:
Pre-set Program 1. (9 til 5)
*The above settings can be understood using the chart below
1
2
3
4
5
6
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period
Room
Temp
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
To adjust these times and temperatures
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Basic Settings
Your Di2RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1)
(Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Di2RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Di2RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Di2RF
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Once the time has been set
press
to confirm and
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Certification Mark
Drayto n
Digist at +2RF
Digist at +2RF
Digist at +2RF
Digist at +2RF
Drayto n
Drayto n
Drayto n
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
06490097001 IssA 24-1-07 13/2/07 11:59 Page 1
Drayton
Di2RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: [email protected]
User Guide 06490097001 IssA
Programmable Room
Thermostat Wireless
24 Hour
Model: RF700/22090
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Di2RF thermostat is a programmable thermostat 24-Hour
product (the same program for every day of the week) which
allows you to set up to 6 time and temperature events per day.
Clock Setting
Your Di2RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Di2RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
The Di2RF thermostat is a programmable thermostat
24-Hour (the same program for every day of the week) and
allows you to set 6 time and temperature events per day.
Di2RF
Pre-set Program
Your Di2RF comes with the following default settings
pre-programmed for your convenience:
Pre-set Program 1. (9 til 5)
*The above settings can be understood using the chart below
1
2
3
4
5
6
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period
Room
Temp
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
To adjust these times and temperatures
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Basic Settings
Your Di2RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1)
(Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Di2RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Di2RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Di2RF
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Once the time has been set
press
to confirm and
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Certification Mark
Drayto n
Digist at +2RF
Digist at +2RF
Digist at +2RF
Digist at +2RF
Drayto n
Drayto n
Drayto n
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
06490097001 IssA 24-1-07 13/2/07 11:59 Page 1
Drayton
Di2RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: [email protected]
User Guide 06490097001 IssA
Programmable Room
Thermostat Wireless
24 Hour
Model: RF700/22090
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Di2RF thermostat is a programmable thermostat 24-Hour
product (the same program for every day of the week) which
allows you to set up to 6 time and temperature events per day.
Clock Setting
Your Di2RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Di2RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
The Di2RF thermostat is a programmable thermostat
24-Hour (the same program for every day of the week) and
allows you to set 6 time and temperature events per day.
Di2RF
Pre-set Program
Your Di2RF comes with the following default settings
pre-programmed for your convenience:
Pre-set Program 1. (9 til 5)
*The above settings can be understood using the chart below
1
2
3
4
5
6
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period
Room
Temp
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
To adjust these times and temperatures
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Basic Settings
Your Di2RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1)
(Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Di2RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Di2RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Di2RF
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Once the time has been set
press
to confirm and
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Certification Mark
Drayto n
Digist at +2RF
Digist at +2RF
Digist at +2RF
Digist at +2RF
Drayto n
Drayto n
Drayto n
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
06490097001 IssA 24-1-07 13/2/07 11:59 Page 1
Drayton
Di2RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: [email protected]
User Guide 06490097001 IssA
Programmable Room
Thermostat Wireless
24 Hour
Model: RF700/22090
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Di2RF thermostat is a programmable thermostat 24-Hour
product (the same program for every day of the week) which
allows you to set up to 6 time and temperature events per day.
Clock Setting
Your Di2RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Di2RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
The Di2RF thermostat is a programmable thermostat
24-Hour (the same program for every day of the week) and
allows you to set 6 time and temperature events per day.
Di2RF
Pre-set Program
Your Di2RF comes with the following default settings
pre-programmed for your convenience:
Pre-set Program 1. (9 til 5)
*The above settings can be understood using the chart below
1
2
3
4
5
6
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period
Room
Temp
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
To adjust these times and temperatures
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Basic Settings
Your Di2RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1)
(Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Di2RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Di2RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Di2RF
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Once the time has been set
press
to confirm and
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Certification Mark
Drayto n
Digist at +2RF
Digist at +2RF
Digist at +2RF
Digist at +2RF
Drayto n
Drayto n
Drayto n
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
06490097001 IssA 24-1-07 13/2/07 11:59 Page 1
8
Installation & User Guide
06
51
5086
0
0
1 I
SS
C
