Draytek VigorAP 810 User Manual Download

Page: 91 / 134

VigorAP 810 User’s Guide

Station List

provides the knowledge of connecting wireless clients now along with its status

code.

Available settings are explained as follows:

Item Description

General/Advanced

General

– Display general information (e.g., MAC Address,

SSID, Auth, Encrypt, TX/RX Rate) for the station.

Advanced

– Display more information (e.g., AID, PSM,

WMM, RSSI PhMd, BW, MCS, Rate) for the station.

MAC Address

Display the MAC Address for the connecting client.

SSID

Display the SSID that the wireless client connects to.

Auth

Display the authentication that the wireless client uses for
connection with such AP.

Encrypt

Display the encryption mode used by the wireless client.

Tx Rate/Rx Rate

Display the transmission /receiving rate for packets.

Refresh

Click this button to refresh the status of station list.

Add to Access
Control

Client’s MAC Address

- For additional security of wireless

access, the Access Control facility allows you to restrict the
network access right by controlling the wireless LAN MAC
address of client. Only the valid MAC address that has been
configured can access the wireless LAN interface.

Add

Click this button to add current typed MAC address into

Access Contro

Summary of Contents for VigorAP 810







































































































































Search results

Summary of Contents for VigorAP 810

Reviews:

Related manuals for VigorAP 810

Brands by name

Popular brands

Draytek VigorAP 810, User Manual

Search results

Summary of Contents for VigorAP 810

Reviews:

Related manuals for VigorAP 810

Brands by name

Popular brands