6. Identification and Unpacking
Please visit
drapertools.com for our full range of accessories and consumables.
EN
– 9 –
– 8 –
EN
1
Fig.
3
Fig.
4
Fig.
2
Fig.
Important: Read and understand all the safety
instructions listed in this manual before attempting
to assemble this product.
Important: Ensure all bolts are only FINGER TIGHT until
assembly is complete. Then tighten all fixtures securely.
7.1 Assemble the Legs
7.2 Attach the Top Frames
1. Place the rear
left leg (C) on your left and the front
left leg (A) on your right so that the indented sides are
at the bottom and facing
towards you.
Important: The folding brace should also be facing
towards you.
2. Open the folding brace (7) and the diagonal brace
(8) and align them with the hole halfway up the left
front leg.
Important: The leg should be positioned between the
two braces, with the lipped edges of the braces facing
upward. The folding leg should be able to fold upward.
3. Pass an M8 x 45mm half-thread hex bolt (N) through
both braces and the leg and secure them in place
with an M8 nylon-insert lock nut (S).
Important: Place an M8 washer (Q) between each
brace and the leg to ensure smooth folding.
4. Attach a foot (M) to the indented end of each leg so
that the longest edge is positioned outwardly on the
same side as the folding brace.
5. Repeat these steps for the front right (B) and rear right
(D) legs, with the rear leg on your
left and the front
leg on your
right.
6. Insert the upper ends of the
left leg assembly
between the brackets of a top frame (I) so that the
holes align and the crank handle (2) is positioned
above the front leg (A).
7. Pass two M8 x 45mm half-thread hex bolts (N) each
through an M8 washer (Q) and top frame bracket
around the leg and secure each in place with another
M8 washer and an M8 nylon-insert lock nut (S).
8. Repeat these steps for the right leg assembly,
ensuring that the crank handle is positioned over
the
front leg.
7. Assembly Instructions
6.3 Packaging
Keep the product packaging for the duration of the
warranty period for reference should the product need to
be returned for repair.
WARNING! Keep packaging materials out of reach
of children. Dispose of packaging correctly and
responsibly and in accordance with local regulations.
(A) 1 x Front left leg
(B) 1 x Front right leg
(C) 1 x Rear left leg
(D) 1 x Rear right leg
(E) 1 x Front crossbar
(F) 1 x Rear crossbar
(G) 1 x Front benchtop
(H) 1 x Rear benchtop
(I)
2 x Top frames
(J) 2 x U-brackets (bare)
(K) 2 x U-brackets with guide plates
(L) 4 x Clamp blocks
(M) 4 x Feet
(N) 6 x M8 x 45mm half-thread hex bolts
(O) 8 x M6 x 37mm half-thread screws
(P) 16 x M5 x 16mm self-tapping screws
(Q) 12 x M8 washers
(R) 8 x M6 washers
(S) 6 x M8 nylon-insert lock nuts
(T) 8 x M6 nylon-insert lock nuts
(U) 1 x Spanner tool
U1. M8 spanner
U2. M6 spanner
6.2 What’s in the Box?
Carefully remove the product from the packaging and
examine it for any signs of damage that may have
occurred during shipment.
Before assembling the product, lay the contents out and
check them against the parts shown below. If any part is
damaged or missing, do not attempt to use the product.
Please contact the Draper Tools Helpline; contact details
can be found at the back of this manual.
(D)
(C)
(A)
(U2)
(U)
(O)
(U1)
(I)
(H)
(A)
(C)
(A)
(G)
(M)
(I)
(F)
(E)
(L)
(M) (J)
(K)
(B)
(P)
(T)
(S)
(Q)
(N)
(R)
(C)
(I)
(N)
(Q, S)
(N)
(S)
(Q)
