background image

2   

Caution Statements

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

DO NOT OPEN THE CABINET; REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION

CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO

PREVENT BLADE EXPOSURE.

POUR PREVENIR LES CHOCS ELECTRIQUES, NE PAS UTILISER CETTE FICHE POLARISEE

AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COUR-

ANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE

PARTIE A DECOUVERT.

WARNING:

CAUTION:

ATTENTION:

A product and cart combination should be moved

with care.  Quick stops, excessive force and uneven

surfaces may cause the product and cart combination 

to overturn.

The lightning flash with arrow head symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying

the product.

CAUTION

WARNING: TO PREVENT FIRE OR

ELECTRICAL SHOCK, DO NOT

EXPOSE TO RAIN OR MOISTURE

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

DO NOT REMOVE COVER

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED PERSONNEL

The MEQ1000A and its associated input modules have been designed to comply with, and tested to confirm

compliance to the following safety regulations:

ANSI/UL 60065, 7th Edition, dated 06/30/2004, rev. 11/20/2006,

CAN/CSA - C22.2 No. 60065:03 (2006). 

ELECTRIC SHOCK,

Summary of Contents for MEQ1000A





















Reviews: