20.11.2015
Specifications are subject to change for improvement without prior notice.
Operating instructions
1.
Intended use
. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum
capacity
is
indicated
in
the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3.
Switching ON/OFF the power tool.
First check
cable and plug for damage. Slide the switch pad
(5)
BACKWARD for switching ON
the power
tool. Slide the switch pad (5)
FORWARD for
switching OFF
the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For
cutting out
curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a
small strip
remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9.
Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled
, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1
2
3
4
5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2
The machine must not be used in a wet environment.
3
Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5
Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
l
Do not carry the machine by the cable.
l
Always remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
l
Always place the cable to the rear away from the
machine.
l
Apply the machine to the sheet metal only when
switched on.
l
Always provide for secure footing when working.
l
Firmly clamp the work piece if it does not remain
stationary from its own weight.
l
The knife should not rub on the jaws: Possible danger
of cutting tool breakage.
l
Do not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
F
For further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min
-1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0
ó
I
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015
Specifications are subject to change for improvement without prior notice.
Operating instructions
1.
Intended use
. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum
capacity
is
indicated
in
the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3.
Switching ON/OFF the power tool.
First check
cable and plug for damage. Slide the switch pad
(5)
BACKWARD for switching ON
the power
tool. Slide the switch pad (5)
FORWARD for
switching OFF
the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For
cutting out
curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a
small strip
remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9.
Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled
, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1
2
3
4
5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2
The machine must not be used in a wet environment.
3
Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5
Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
l
Do not carry the machine by the cable.
l
Always remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
l
Always place the cable to the rear away from the
machine.
l
Apply the machine to the sheet metal only when
switched on.
l
Always provide for secure footing when working.
l
Firmly clamp the work piece if it does not remain
stationary from its own weight.
l
The knife should not rub on the jaws: Possible danger
of cutting tool breakage.
l
Do not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
F
For further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min
-1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0
ó
I
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015
Specifications are subject to change for improvement without prior notice.
Operating instructions
1.
Intended use
. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum
capacity
is
indicated
in
the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3.
Switching ON/OFF the power tool.
First check
cable and plug for damage. Slide the switch pad
(5)
BACKWARD for switching ON
the power
tool. Slide the switch pad (5)
FORWARD for
switching OFF
the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For
cutting out
curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a
small strip
remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9.
Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled
, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1
2
3
4
5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2
The machine must not be used in a wet environment.
3
Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5
Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
l
Do not carry the machine by the cable.
l
Always remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
l
Always place the cable to the rear away from the
machine.
l
Apply the machine to the sheet metal only when
switched on.
l
Always provide for secure footing when working.
l
Firmly clamp the work piece if it does not remain
stationary from its own weight.
l
The knife should not rub on the jaws: Possible danger
of cutting tool breakage.
l
Do not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
F
For further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min
-1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0
ó
I
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015
Specifications are subject to change for improvement without prior notice.
Operating instructions
1.
Intended use
. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum
capacity
is
indicated
in
the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3.
Switching ON/OFF the power tool.
First check
cable and plug for damage. Slide the switch pad
(5)
BACKWARD for switching ON
the power
tool. Slide the switch pad (5)
FORWARD for
switching OFF
the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For
cutting out
curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a
small strip
remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9.
Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled
, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1
2
3
4
5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2
The machine must not be used in a wet environment.
3
Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5
Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
l
Do not carry the machine by the cable.
l
Always remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
l
Always place the cable to the rear away from the
machine.
l
Apply the machine to the sheet metal only when
switched on.
l
Always provide for secure footing when working.
l
Firmly clamp the work piece if it does not remain
stationary from its own weight.
l
The knife should not rub on the jaws: Possible danger
of cutting tool breakage.
l
Do not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
F
For further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min
-1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0
ó
I
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015
Specifications are subject to change for improvement without prior notice.
Operating instructions
1.
Intended use
. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum
capacity
is
indicated
in
the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3.
Switching ON/OFF the power tool.
First check
cable and plug for damage. Slide the switch pad
(5)
BACKWARD for switching ON
the power
tool. Slide the switch pad (5)
FORWARD for
switching OFF
the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For
cutting out
curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a
small strip
remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9.
Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled
, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1
2
3
4
5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2
The machine must not be used in a wet environment.
3
Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5
Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
l
Do not carry the machine by the cable.
l
Always remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
l
Always place the cable to the rear away from the
machine.
l
Apply the machine to the sheet metal only when
switched on.
l
Always provide for secure footing when working.
l
Firmly clamp the work piece if it does not remain
stationary from its own weight.
l
The knife should not rub on the jaws: Possible danger
of cutting tool breakage.
l
Do not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
F
For further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min
-1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0
ó
I
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015
Specifications are subject to change for improvement without prior notice.
Operating instructions
1.
Intended use
. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum
capacity
is
indicated
in
the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3.
Switching ON/OFF the power tool.
First check
cable and plug for damage. Slide the switch pad
(5)
BACKWARD for switching ON
the power
tool. Slide the switch pad (5)
FORWARD for
switching OFF
the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For
cutting out
curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a
small strip
remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9.
Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled
, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1
2
3
4
5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2
The machine must not be used in a wet environment.
3
Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5
Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
l
Do not carry the machine by the cable.
l
Always remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
l
Always place the cable to the rear away from the
machine.
l
Apply the machine to the sheet metal only when
switched on.
l
Always provide for secure footing when working.
l
Firmly clamp the work piece if it does not remain
stationary from its own weight.
l
The knife should not rub on the jaws: Possible danger
of cutting tool breakage.
l
Do not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
F
For further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min
-1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0
ó
I
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
