DR FIELD and BRUSH MOWER Safety & Operating Instructions Manual Download Page 34

34

 

        

DR

®

 

 FIELD and BRUSH MOWER

 

Parts List – Frame and Drive Assembly 

NOTE:

 

Part numbers listed are available through DR Power Equipment.

 

Ref# Part# 

Description 

01 150261  Frame, 

Main 

02 

111581 

Bolt, 5/16"-18 x 1", HCS, GR2 

03 150181  Guard, 

Chain 

04 

187551 

Nut, Nylon Lock, 5/16"-18, Lo-Profile 

05 110691  Nut, 

5/16"-18 

06 

112381 

Washer, Flat, 1/4" USS 

07 

164801 

Spring, Extension, .750" OD x FL 

08 

150101 

Bushing, .328" ID, .500" OD, 2.32" L 

09 

150481 

Pulley, Flat Idler, 1.88" OD, .375" Bore 

10 

164781 

Idler Arm, Inner, Chain Adjust 

11 

164771 

Idler Arm, Outer, Chain Adjust 

12 

126861 

Bolt, 3/8"-16 x 3", HCS, GR5 

13 

110751 

Nut, Nylon Lock, 3/8"-16 

14 

111731 

Screw, 5/16"-18 x 1/2", Tri-Lobe 

15 

112431 

Washer, Lock, 5/16", Split 

16 

150291 

Fuel Tank Assembly, 2.5 Gallons 

17 

153531 

Conduit, Split, 7/16" 

18 

100661 

Clamp, Fuel Line 

19 

211661 

Hose, Fuel, 1/4" ID, CA Certified 

20 

110731 

Nut, Nylon Lock, 1/4"-20 

21 

150531 

Strap, 2.5 Gallon Fuel Tank 

22 

112481 

Washer, Lock, 1/4" External Tooth 

23 

114701 

Bolt, 1/4"-20 x 1/2", HCS, GR5 

24 

280761 

Mount, Fuel Tank 

Ref# Part# 

Description 

25 

110761 

Nut, Nylon Lock, 5/16"-18 

26 

123211 

Bolt, 5/16"-18 x 3/4", HCS, GR5 

27 

150171 

Support, Chain Idler 

28 

151151 

Washer, 1.38" ID, 2.00" OD, for Pin 

29 

150461 

Pin, Detent, 1/4" x 2" 

30 

151381 

Washer, 1.375" ID, 2.00" OD, x .25" 

31 

192891 

Wheel & Tire, 18" x 6.50"- 8", Terrain, 5 
Lug, Grey 

 

150621 

Wheel & Tire, 18" x 6.50"- 8", Terrain, 5 
Lug, White 

 

151721 

Wheel & Tire, 18" x 6.50"-8", Turf, 5 Lug, 
White 

 

209371 

Wheel Stud, 1/2"-20 

32 165221  Nut, 

Lug, 

1/2"-20 

33 151971  Split 

Collar, 

1.00" ID x 1.75" OD, Clamp-

On w/Set Screws 

34 

192301 

Differential, Lock In/Out 

35 

150191 

Chain, #40, 88 Pitches with Master Link 

36 

193511 

Spring, E, 1/2" OD, .069 Wire x 4" L, ZP 

37 

190581 

Cam, Lock In/Out Differential 

38 

190601 

Support Assembly, Pivot, Lock In/Out 

39 192321  Screw, 

Shoulder, 1/4"-20, Lock, .312" 

Body 

40 

187571 

Bolt, 5/16"-18 x 3-3/4", HCS 

41 

190591 

Bracket, Cam Pivot, Lock In/Out 

  

Summary of Contents for FIELD and BRUSH MOWER









































Reviews: