manualshive.com logo in svg

Dover PSG Wilden PS1520, Engineering, Operation & Maintenance, Page: 14 / 32

Share
Download
Dover PSG Wilden PS1520 Engineering, Operation & Maintenance Download Page 14

WILDEN PUMP & ENGINEERING, LLC 

12 

WIL-11520-E-07

NOTE: In the event of a power failure, the shut-off 
valve should be closed, if the restarting of the pump is 
not desirable once power is regained.

AIR-OPERATED PUMPS: To stop the pump from 
operating in an emergency situation, simply close 
the shut-off valve (user-supplied) installed in the air 
supply line. A properly functioning valve will stop the 
air supply to the pump, therefore stopping output. This 
shut-off valve should be located far enough away from 
the pumping equipment such that it can be reached 
safely in an emergency situation.

AIR SHUT-OFF VALVE

NEEDLE VALVE

FOOTPAD

COMBINATION

FILTER & REGULATOR

SUCTION

MUFFLER

FLEXIBLE

CONNECTION

FLEXIBLE

CONNECTION

GAUGE

(OPTIONAL)

EQUALIZER

SURGE DAMPENER

(OPTIONAL)

SHUT-OFF

VALVE

DISCHARGE

This illustration is a generic 
representation of an air-operated 
double-diaphragm pump.

S U G G E S T E D   I N S T A L L A T I O N

Summary of Contents for PSG Wilden PS1520

































Reviews:

No comments