manualshive.com logo in svg

Dover PSG Mouvex AZ O, Installation Operation & Maintenance

Share
Download
Dover PSG Mouvex AZ O Installation Operation & Maintenance Download Page 3

3/19

NT 1003-A00 09 18 AZ O  e

1. OVERALL DIMENSIONS

Weight

: 6 kg 

(7 kg with 

support 

foot)

The pump can be delivered with support foot pump or not to
be flanged.

The pump can be fixed in any position.

Chain or belt drive.

Shaft end supported by ball-bearing.

Place pulley as near as possible to ball-bearing.

E

Bypass valve.

I

Space required for removing pump.

P

Pump plate.

PAT

Support foot pump.

S

Mounting point for probe : M6 - threaded width : max. 8 mm.

Noise level

The sound level of a pump is greatly influenced by its condi-
tions of use. Cavitation and pumping products with high gas
contents generally increases the sound level.

Under the following pumping conditions :

• excluding cavitation

• discharge pressure : 5 bar

• speed of rotation 1500 rpm

• product viscosity of 1 cSt

The sound level reached for the AZ pump in good conditions
(ignoring the motor and gearbox noise) is less than 77 dB(A).

Summary of Contents for PSG Mouvex AZ O




















Reviews:

No comments

Brands by name

Popular brands

Load more brands