manualshive.com logo in svg

Dover PSG Mouvex AZ O, Installation Operation & Maintenance

Share
Download
Dover PSG Mouvex AZ O Installation Operation & Maintenance Download Page 12

12/19

NT 1003-A00 09 18 AZ O  e

6. BYPASS (continued)

6.3 Inversion

Before commencing work, make sure that the pump
cannot be started up, even accidentally. Before opening
the pump, it must be drained and relieved of any pressu-
re it may contain. Take care to check that the isolation
valves, if any, are closed  before pulling out the drain
plug 

812

and its seal 

848

.

To reverse the bypass, remove the nut 

808

and the set

of parts 

805

- 

806

- 

807

- 

809

and 

810

. Remove the

valve 

803

, its spring 

804

and fit those parts on the oppo-

site side.

Fit the plug 

812

and the seal 

848

in the place of the nut

808.

6.4 Adjustment

To adjust the bypass, unscrew the cap 

810

and its seal

809

, turn the adjustment screw 

806

clockwise to increa-

se the discharge pressure, and anticlockwise to decrea-
se it. Once the adjustment is finished, do not forget to re-
screw the cap 

810

and its seal 

809.

Adjustment of the bypass is satisfactory when the flow
meets the pumps requirements and when the motor
bears the power increase due to the overpressure seen
upon closing the discharge. This is how the bypasses of
our pump units are adjusted, as a function of the infor-
mation provided by our Technical Services.

The pumps supplied bare shaft are delivered with a
standard bypass setting which needs to be adjusted with
the exact working conditions and installation, as per the
above described procedure.

WARNING

FAILURE TO RELIEVE SYSTEM
PRESSURE PRIOR TO PERFORMING
PUMP SERVICE OR MAINTENANCE
CAN CAUSE PERSONAL INJURY OR
PROPERTY DAMAGE.

Hazardous pressure 

can cause 

personal injury 

or property damage.

WARNING

PUMPS OPERATING AGAINST A CLO-
SED VALVE CAN CAUSE SYSTEM
FAILURE, PERSONAL INJURY AND
PROPERTY DAMAGE.

Hazardous pressure 

can cause 

personal injury 

or property damage.

WARNING

IF PUMPING HAZARDOUS OR TOXIC
FLUIDS, THE SYSTEM MUST BE FLUS-
HED PRIOR TO PERFORMING ANY
SERVICE OPERATION.

Hazardous or toxic

fluids can cause 

serious injury.

WARNING

DISCONNECT THE ELECTRICITY
SUPPLY BEFORE ANY MAINTENAN-
CE OPERATION.

Dangerous voltage.

Can cause 

injury and death.

WARNING

BE CAREFUL WITH THE WEIGHT OF
THE PARTS WHEN THEY ARE BEING
REMOVED.

The weight ot the parts

can be dangerous and

may provoke bodily inju-

ries 

or material damages.

Loading (bar)

Mini

Maxi

1,65

5

Summary of Contents for PSG Mouvex AZ O




















Reviews:

No comments

Brands by name

Popular brands

Load more brands