manualshive.com logo in svg

Dover H-20905-PA, Installation, Operation & Maintenance Manual, Page: 6 / 24

Share
Download
Dover H-20905-PA Installation, Operation & Maintenance Manual Download Page 6

IMPORTANT:  

OPW products should be used in compliance with applicable federal, state, provincial, and local laws and regulations. Product selection should be 

based on physical specifications and limitations and compatibility with the environment and materials to be handled. OPW MAKES NO WARRANTY OF FITNESS 

FOR A PARTICULAR USE. All illustrations and specifications in this literature are based on the latest product information available at the time of publication. OPW 

reserves the right to make changes at any time in prices, materials, specifications and models and to discontinue models without notice or obligation.

6

Drylok

®

 Dry Disconnect – 1" Adaptor

Drylok

®

 Dry Disconnect 1" Adaptor  – H-31296-PA

ITEM

QTY

DESCRIPTION

1

1

Body, Adaptor, 5670, FNPT, SST, 1"

2

1

Bridge, Adaptor, 5670, SST, 1"

3

1

Poppet ASM, Adaptor, 5670, SST, 1"

4

1

Spring, Adaptor, 5670, SST, 1"

5

1

O-Ring, Fluorocarbon, 211"

Summary of Contents for H-20905-PA

























Reviews:

No comments