Douglas Dynamics WESTERN ENFORCER 94040-3 Installation Instructions Manual Download Page 3

Lit. No. 74914, Rev. 01 

June 1, 2020

HYDRAULIC SAFETY

•  Always inspect hydraulic components and hoses 

before using. Replace any damaged or worn parts 

immediately.

•  If you suspect a hose leak, DO NOT use your 

hand to locate it. Use a piece of cardboard or 

wood.

FUSES

The WESTERN

®

 electrical and hydraulic systems 

contain several automotive‑style fuses. If a problem 

should occur and fuse replacement is necessary, 

the replacement fuse must be of the same type and 

amperage rating as the original. Installing a fuse with 

a higher rating can damage the system and could start 

a fire. Fuse Replacement, including fuse ratings and 

locations, is located in the Maintenance section of the 

Owner's Manual.

PERSONAL SAFETY

•  Remove ignition key and put the vehicle in PARK 

or in gear to prevent others from starting the 

vehicle during installation or service.

• 

Wear only snug-fitting clothing while working on 

your vehicle or snowplow.

•  Do not wear jewelry or a necktie, and secure long 

hair.

•  Wear safety goggles to protect your eyes from 

battery acid, gasoline, dirt, and dust.

•  Avoid touching hot surfaces such as the engine, 

radiator, hoses, and exhaust pipes.

• 

Always have a fire extinguisher rated BC handy for 

flammable liquids and electrical fires.

 WARNING

Hydraulic fluid under pressure can cause skin 

injection injury. If you are injured by hydraulic 

fluid, get medical attention immediately.

SAFETY

SAFETY PRECAUTIONS

Improper installation and operation could cause 

personal injury and/or equipment and property damage. 

Read and understand labels and the Owner's Manual 

before installing, operating, or making adjustments.

 WARNING

Lower the blade when vehicle is parked. 

Temperature changes could change 

hydraulic pressure, causing the blade to 

drop unexpectedly or damaging hydraulic 

components. Failure to do this could result in 

serious personal injury.

 WARNING

Remove blade assembly before placing 

vehicle on hoist.

 WARNING

The driver shall keep bystanders clear of the 

blade when it is being raised, lowered, or 

angled. Do not stand between the vehicle and 

the blade or within 8 feet of a moving blade. A 

moving or falling blade could cause personal 

injury.

 WARNING

Do not exceed GVWR or GAWR including 

blade and ballast. The rating label is found on 

driver-side vehicle door cornerpost.

 WARNING

To prevent accidental movement of the blade, 

always turn the control OFF whenever the 

snowplow is not in use. The power indicator 

light will turn OFF.

 WARNING

Keep hands and feet clear of the blade and 

T-frame when mounting or removing the 

snowplow. Moving or falling assemblies could 

cause personal injury.

 CAUTION

Refer to the current Quick Match 

selection system for minimum vehicle 

recommendations and ballast requirements.

Summary of Contents for WESTERN ENFORCER 94040-3



















Reviews: