background image

GUANGDONG DOROSIN ELECTRICAL

APPLIANCE CO., LTD.

3

1. IMPORTANT NOTICE

Always keep the unit in vertical position and on a firm flat surface at all times.

Ensure that there is at least 300mm (1”) between the sides of the appliance and any

flammable, heating materials.

Do not place on soft surfaces.

Do not cover the appliances intake or outlet grilles.

For indoor use only.

Not suitable for use in cabinet, closet, boats, caravans or similar locations.

Leave the unit to stand for one hour before connecting to the mains supply after

transport or when it has been tilted (e.g. during cleaning).

Do not obstruct the air intakes and exhausts.

The mains supply must conform to the specification shown on the rating plate at the

back of the unit.

Avoid overloading circuits, which is caused by using more electrical amps than your

wiring can support. Overloading electrical wires can cause excessive heat and

electrical fires.

Avoid the appliance from splash.

Examine the cord carefully. Make sure that it is not punctured or frayed. Inspect the

plug to ensure that the prongs are secure and the plastic surrounding it is not cracked.

Avoid running cords under carpets and other areas where you cannot regularly check

their condition.

Avoid over-twisting, -coiling, -pulling the power cord, never use nylon or iron wire to

tide the power cord.

Do not leave appliance when plugged in, unplug from outlet when not in use and

before servicing. Connect to a grounded outlet only.

If the supply cord is damaged, it must be replaced by an approved service

representative or a similar qualified person in order to avoid a hazard.

Never use the plug to start and stop the unit. Always use switch on the control panel.

Before moving the unit, turn off all controls, then unplug and empty the water tank.

Don't use bug sprays or other flammable cleaners on the unit.

Never pour or spray water over the unit.

This appliance can be used by children aged from 8 years and above and persons with

Summary of Contents for ERS-860L
























Reviews: