4. Commissioning
5. Adjustments
Work on the electrical equipment must only be
performed by trained and properly qualified
electricians.
Basic requisites
4.1 Implementing the factory settings (initialisation -
this sets the operator to the factory defaults).
On the control board:
During the learning cycle, the latching action
adjustment valve must be closed.
Backcheck parameter
pushbuttons T1
and T2
pushbutton T1
T2
LED 1 (green)
·
·
·
·
The operator is fully assembled and installed.
All cabling and wiring has been completed.
The door operates smoothly.
Optional accessories have been installed and hooked
up in accordance with the wiring diagram.
Depress pushbutton T1 while simultaneously
switching on the mains supply.
- Release pushbutton T1.
- Check the latching action valve and close if still open.
Depress pushbutton T1 for approx. 3 s.
- LED 1 (green) flashes.
The
(e.g. for room ventilation) is stored by the
control unit.
The opening angle is stored by the control unit as the
full opening angle.
- The door closes.
adjustable in 7 increments from 3.0 to 6.0 seconds.
adjustable in 5 increments from 70° to 90°.
can be toggled ON or OFF.
can be toggled ON or OFF.
On the control board you will find
. The parameterisation mode is activated by
pressing these two pushbuttons simultaneously.
If the mode is already active, use
to
select the parameter and
to change the parameter
settings. Operation of the pushbuttons is extremely
simple in that they can only be used to select the
next parameter or the next highest setting. Once the
last parameter or the highest setting has been
reached, the count returns to the first parameter or
the lowest setting.
shows which parameter has been
activated by the number offl ashes per sequence.
- Set the program switch to OFF.
Set program switch to OFF.
Release pushbutton T1.
The operator is now ready for programming the
opening angle.
- Open the door manually until the required opening
angle for the extended hold-open function has been
reached and then hold the door in this position.
- Briefly press pushbutton T1.
opening angle for the extended hold-open
function
- Open the door manually to the required full opening
angle and hold the door in this position.
- Briefly press pushbutton T1.
adjustable in 4 increments from 0 to 0.8 Sekunden.
adjustable in 5 increments from 15° to 35°.
adjustable in deactiv, low activ, high activ.
adjustable in hinge side (BS), opposite hinge side
(BGS), hinge side and opposite hinge side.
After approx. 10 seconds, the green LED 1 will
flash two times.
LED 1 (green) should immediately switch to
continuous glow, indicating that the factory
defaults have been implemented.
The control unit of the CD 80 is now set to the
values indicated in the table.
The learning cycle has been completed.
The operator is on standby ready for activation.
adjustable in 10 increments from 0 to 30 seconds.
indicates the currently set value by
the number offl ashes per sequence.
Default values
4.2 Starting the learning cycle.
4.3 Setting the extended hold-open function.
4.4 Adjusting the full opening angle
4.5 The door automatically performs two opening
cycles, during which it determines the door weight
and spring compensation value.
4.6 LED 1 (green) glows continuously.
5.1 The following parameters can be adjusted in
the parameterisation mode:
Opening time parameter
Hold-open time parameter
Wall blanking parameter
Push&Go parameter
Power Assist parameter
5.2. Activating the parameterisation mode
LED 2 (red)
-
-
-
Delayed opening for locking mechanism parameter
Sensortest-level parameter (testlevel activ)
Sensortest-sensor Parameter (zu testende Sensoren)
4. Commissioning/5. Adjustment/6. Functional testing
Opening position
Opening time
Hold-open time
Wall blanking
Push&Go
Power Assist Mode
Dela ed opening for
locking mecanism
Backcheck
Sensortest-level
Sensortest- ensor
y
s
90° for top-jamb fixing
4 s
5 s
80°
0 not active
0 not active
0,3 s
15°
deactiv
BS (pull side)
4. Commissioning (continue)
5. Adjustments
Backcheck parameter
pushbuttons T1
and T2
pushbutton T1
T2
LED 1 (green)
The opening angle is stored by the control unit as the
full opening angle.
- The door closes.
adjustable in 7 increments from 3.0 to 6.0 seconds.
adjustable in 5 increments from 70° to 90°.
can be toggled ON or OFF.
can be toggled ON or OFF.
On the control board you will find
. The parameterisation mode is activated by
pressing these two pushbuttons simultaneously.
If the mode is already active, use
to
select the parameter and
to change the parameter
settings. Operation of the pushbuttons is extremely
simple in that they can only be used to select the
next parameter or the next highest setting. Once the
last parameter or the highest setting has been
reached, the count returns to the first parameter or
the lowest setting.
shows which parameter has been
activated by the number offl ashes per sequence.
- Open the door manually to the required full opening
angle and hold the door in this position.
- Briefly press pushbutton T1.
adjustable in 4 increments from 0 to 0.8 Sekunden.
adjustable in 5 increments from 15° to 35°.
adjustable in deactiv, low activ, high activ.
adjustable in hinge side (BS), opposite hinge side
(BGS), hinge side and opposite hinge side.
The learning cycle has been completed.
The operator is on standby ready for activation.
adjustable in 10 increments from 0 to 30 seconds.
indicates the currently set value by
the number offl ashes per sequence.
4.5 The door automatically performs two opening
cycles, during which it determines the door weight
and spring compensation value.
4.6 LED 1 (green) glows continuously.
5.1 The following parameters can be adjusted in
the parameterisation mode:
Opening time parameter
Hold-open time parameter
Wall blanking parameter
Push&Go parameter
Power Assist parameter
5.2. Activating the parameterisation mode
LED 2 (red)
Delayed opening for locking mechanism parameter
Sensortest-level parameter (testlevel activ)
Sensortest-sensor Parameter (zu testende Sensoren)
4. Commissioning/5. Adjustment
CD 80
Swing Door Operator
DORMA
9
DORMA AUTOMATICS, Inc.
924 Sherwood Drive
Toll-Free: 877-367-6211
DL2862-010
Lake Bluff, IL 60044
Fax: 877-423-7999
Jan. 2007
E-mail: [email protected]
Subject to change without notice
Example:
Parameter, LED flashing rhythms and settings
LED 1 (green) flashes once
- the opening time parameter is activated
LED 2 (rot) flashes three times
- the value for the opening time is 4.0 s.
The following table shows the factory defaults for the
parameters in emboldened print.
Pause
Pause
1x 2x 3x
Pause Pause
1x
Wall blanking
Delayed opening
for locking
mechanism
LED 1
flashes
Hold-open time
Opening time
LED 2
flashes
Parameter
settings
Power Assist Mode
Backcheck
Internal
service function
Push&Go
1
2
3
4
6
7
8
9
10
5
3,0 s
3,5 s
4,5 s
5,0 s
5,5 s
6,0 s
4,0 s
1
2
4
5
6
7
3
1
2
1
2
1
2
3
4
5
1
3
4
5
6
2
0 s
0,5 s
0,8 s
1,5 s
2,0 s
0,3 s
1
2
4
5
3
0 s
1 s
2 s
3 s
8 s
10 s
12 s
15 s
30 s
5 s
70°
75°
85°
90°
80°
Off
On
Off
On
15°
20°
25°
30°
35°
1
2
5
7
6
8
4
3
Parameter
