Dorex DX2 FW Installation Instructions Manual Download Page 11

Page: 11 / 16

11 / 16

OPTIONAL DXAS106 STRIKE INSTALLATION

11 / 16

Prepare two (2) holes

and install a screw

through each slot.

Mark four (4)

Holes

CENTER CASE TEMPLATE ALIGNS AS SHOWN

SECURE STRIKE

Roller against door

Align template on

centerline and against

roller of strike.

Strike Screws

ALIGN STRIKE ON HORIZONTAL CENTERLINE

( ) AND MARK TWO(2) SLOTTED HOLES.

Shim

¹⁄8

" DRILL

PILOT 1" DEEP

WOOD

DXAS106

METAL

#25 DRILL

#10-24 TAP

INSTALL STRIKE AND SHIM.

Strike Screw

Shim

DXAS106

Adjust strike closer or further from the door to properly engage with the

latch bolt. Secure strike position; mark hole center for third screw, then

drill/tap as required.

Add/remove shims as required to ensure proper latch-strike engage-

ment without binding.

Use strike as template and place on door stop with roller against

the door. Align strike centerline with the exit device horizontal

centerline on the door and stop. Mark slot centers, then drill/tap

holes as required.

Summary of Contents for DX2 FW

















Search results

Summary of Contents for DX2 FW

Reviews:

Related manuals for DX2 FW

Brands by name

Popular brands

Dorex DX2 FW, Installation Instructions Manual

Search results

Summary of Contents for DX2 FW

Reviews:

Related manuals for DX2 FW

Brands by name

Popular brands