background image

OPERATOR PROGRAMMING

12

Нажмите «+» —
загорится «8»

P

+

-

Нажмая «+» или «–» выберите значение
функции: «0» — выкл., «1» — вкл.

Нажмите «P»

 

Нажмите «P» для сохранения 
информации 

P

+

-

P

+

-

Нажмите «P» 

P

+

-

Нажмите «+» —
загорится «7»

6.7.   Absolute cycle counter

6.8.   Warning alarm setup

6.9.   Automatic closing 

Press “P”

6.10.  Maintenance counter after 2000 cycles (factory setting: «0» – the function is off)

Press «+» 

«5» will light, press 
«P»

The 1st digit will be
displayed

Press «+»

«6» will light, 
press «P»

When pressing «+» and «-», select a function 
value: «0» – off, «1» - on

Press «+», «
7» will light

Press «P»

When pressing «+» and «-», select a function value: «0» - 
 no automatic closing, «1» - pause 30 sec, «2» - pause
60 sec ..., «8» - pause 240 sec.

Press «P» to save the
information

When pressing «+» and «-», select a function 
value: «0»– off, «1» – on

Press «+», 
«8» will light

When entering the 5th point of menu, two digits will be displayed sequentially. After having displayed the digits, the
program returns to main menu.
The first digit – tens, the second digit – units.
The value received is multiplied by 1000 to receive information on amount of cycles driven by the operator.

The 2nd digit will be
displayed

Press «P» to save the
information

Press «P» to save the
information

In the case you forgotten to close the door, after 10 minutes a warning alarm will sound. This signal will be turned off
automatically after the door will be closed. The factory setting of this function is “0” – the function is off.

6.11.  Completing the programming

Press «+» or «-», select «1». Press and hold down «P» until «0» appears on the display. The programming is complete.

Summary of Contents for FAST-750



















Reviews: