background image

 A2

Donaldson™ iCue™ Sensor Integrated Gateway

Canada

Radio Frequency (RF) Exposure Information

The radiated output power of this device is below the Innovation, Science and Economic Development Canada (ISED) radio 

frequency exposure limits. The device should be used in such a manner such that the potential for human contact during normal 

operation is minimized. This device has been evaluated and shown compliant with the ISED RF Exposure limits under mobile 

exposure conditions (antennas are greater than 20 cm from a person's body).
This device has been certified for use in Canada. Status of the listing in the ISED’s REL (Radio Equipment List) can be found at 

the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-

gst.nsf/eng/sf08792.html

Contains IC ID(s): 8595A-2AGQN4NNN

Any changes or modifications made to this device that are not expressly approved by the cellular module manufacturer could void 

the user's authority to operate the equipment.

CLASS B:

Innovation, Science and Economic Development Canada (ISED) Notices

This Class B digital apparatus complies with Canadian CAN ICES-3(B) / NMB-3(B).

Operation is subject to the following two conditions: 

•  This device may not cause interference.
•  This device must accept any interference, including interference that may cause undesired operation of the device.

 

Informations concernant l'exposition aux frux friti radio (RF)

La puissance de sortie émise par l’appareil de sans fil cet appareil est inférieure à la limite d'exposition aux fréquences radio 

d'Innovation, Sciences et Développement économique Canada (ISDE). L'appareil doit être utilisé de manière à minimiser les 

risques de contact humain lors du fonctionnement normal. Ce pe pmal.neme a éa  éa pma et dd ddal. conforme aux limites 

d'exposition aux frux friti radio (RF) d'ISDE lorsqu'il est installl dans des produits hhodu particuliers qui fonctionnent dans des 

conditions d'exposition 'exposappareils mobiles (les antennes se situent ituent ent sicentimt ent du corps d'une personne). 

Ce p. Ce pe). C est homologuu pour l'utilisation au Canada. Pour consulter l'entrna correspondant orlorrespond dans la liste 

d'équipement radio (REL - Radio Equipment List) d'ISDE rendez-vous sur:  http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.

do?lang=fra 
Pour des informations suppllations su concernant l'exposition aux RF au Canada rendez-vous sur: http://www.ic.gc.ca/eic/site/smt-

gst.nsf/fra/sf08792.html  

CLASS B:

Avis d'Innovation, Sciences et Développement économique Canada (ISDE) 

Cet appareil numérique de classe B est conforme aux normes canadiennes CAN ICES-3(B) / NMB-3(B). 

Son fonctionnement est soumis aux deux conditions suivantes: 

•  Cet appareil ne doit pas causer d'interfser d'.
•  Cet appareil doit accepter toute interffnterf, notamment les interfnterfes qui peuvent affecter son fonctionnement.

Summary of Contents for iCue Sensor Integrated Gateway





















Reviews: