25
25
E N G L I S H
1. Lift the console out of its support, remove the battery cover located at the
back of the product, and place four LR14 (1.5 V) batteries in the battery
compartment behind the screen.
2. Make sure the batteries are installed correctly and are flush with the springs.
3. Put the battery compartment lid back on and check to ensure that it is secure.
4. If the display is illegible or incomplete, remove the batteries, wait 15 seconds
and then put them back in.
5. If you remove the batteries, the computer memory is erased.
RECYCLING :
LThe “crossed-out bin” symbol indicates that this product and
the batteries it contains cannot be disposed of with household
waste. They are subject to specific sorting. Take the batteries and
your unusable electronic product to an authorised collection area
for recycling. Recycling your electronic waste will protect the
environment and your health.
400/0000361/12
BATTERY INSTALLATION
- If you note abnormal distances or speeds, check that the switch
behind the console is in the VM position for magnetic bikes and
VE for elliptical bikes. Press the RESET button so that the change
takes effect.
- On magnetic bikes each turn of the pedals corresponds to a
distance of 4 metres, and on elliptical bikes 1 movements corres-
ponds to a distance of 1.6 metres. (These values correspond to
average distances on a bike or walking.)
- If the heart rate indicator (3,12,14) is not flashing or is flashing
erratically, check that your hands are positioned properly and that
the sensors are not too moist.
- If you note that the counter does not display the correct units of
distance, check that the switch behind the console is in the Mi
position to display in miles, or in the Km position to display in
kilometres. Press the RESET button so that the change takes effect.
If the counter does not turn on :
- If you are using the battery: check that the batteries have been
placed in the c/- position.
- If the problem persists, start again with new batteries.
- If the bicycle is connected to the mains: check that the adaptor is
correctly connected to the bicycle.
- In both cases, check that the cables are correctly connected
behind the console and where the stem set joins the main frame of
the bicycle.
If the problem persists: Bring the product back to the nearest
DECATHLON store.
If a noise emanates from inside the casing or you cannot adjust
your intensity level when in manual mode, do not try to repair it.
Bring the product back to the nearest DECATHLON store.
Only use the product with the adaptor supplied.
TROUBLESHOOTING
Summary of Contents for VE 580
