HYDRAULICS INSTALLATION
(after complete unit is assembled)
©2003, ©2004 and ©2005 Fitness Quest
®
Inc.
All rights reserved. Gazelle Power Plus
TM
is a trademark of Fitness Quest
®
Inc.
electronics
water bottle
and holder
cross tube
right frame
left frame
axle tube
right
swing arm
left
swing arm
left
base
frame
handlebars
right
base
frame
left
swing arm
right
frame
left
frame
right
swing arm
poly bag
frame plate
M10 x 95mm
hex bolts
M10 x 95mm
hex bolts
left base frame
right base frame
cross tube
frame plate
To familiarize yourself
with the parts, lay them
out on the floor as
shown. Cables should
lay on top of the frames
(be careful you do not
tangle cables with
swing arms).
Tools Required for Assembly:
Phillips Screwdriver
Wrenches (provided)
Occasionally our products contain components that are pre-lubricated at the factory. We recommend that you protect
flooring, or anything else the parts may contact, with newspaper or cloth.
b. Lying Out Swing Arms
Move the left and right swing arms to the
center of the frame assembly as shown. Make
sure the cables lay on the top of all pieces.
a. Base Frame Assembly
First,
remove the 6, M8 x 25mm bolts and
spring washers on the left and right base
frames marked L and R with the arrows
toward the front.
Second,
use 4 of the M8 x 25mm bolts,
2 on each end, to attach the cross tube to
the top of the base frame.
We recommend having someone
available to help you. Due to the
size and weight of some of the
pieces, assembly is easier and safer
if there are two people.
ASSEMBLY INSTRUCTIONS
fastener pack
M8 x 25mm hex bolt (2),
spring washer and washer
(attaches axle tube to frame)
M6 x 40mm Phillips bolt (4)
(attaches end caps to frame)
wrench (2)
M10 x 95mm hex bolt (4)
and spring washer
(attaches frame plate &
cross tube to base frame)
frame plates
large
washers
end caps
Third,
attach the frame plates to each side
of the base frames using (4) M10 x 95mm
hex bolts and spring washers from the
fastener pack. These bolts also secure the
base frame to the cross tube. Tighten bolts.
front
remove 6
M8 x 25mm
bolts from
left base
replace 2
M8 x 25mm
bolts to attach
cross tube
replace 2
M8 x 25mm
bolts to attach
cross tube
remove 6
M8 x 25mm
bolts from
right base
1/20/05
mounting
bracket
foot tube
washer
nut
left
swing
arm
left side
shown
M8 x 70mm
hex bolts
hydraulics
pin
fastener pack
closed end
wrenches
clips
springs
M8 x 70mm hex bolts,
washers and nylon nuts
mounting brackets
washers (4)
12mm
washers (2)
8mm
rubber pad (4)
nut caps
nuts
If you do not wish to use the hydraulics,
remove the clips and move the hydraulics into
the zero resistance slot. Replace both clips.
NOTE:
There are 4 levels of resistance on the
unit. Begin exercising at Level 1 (zero resistance)
and slowly advance to the next level when the
current level becomes too easy. The levels
increase as you move the pin towards you to
the next position.
Zero
Resistance
Level 1
Level
2
Level
3
Level
4
RESISTANCE LEVELS
TO INSTALL YOUR HYDRAULICS
left
right
clip in zero resistance
PARTS
a
.
Fasten mounting brackets
to the outside edges of the
left and right foot tubes using
(2) hex bolts, (2) washers and
(2) nylon nuts. Tighten bolts
with wrenches provided.
d
.
Pull left hydraulic down to allow pin to pass
through resistance hole in mounting bracket. For
ease of assembly, raise foot platform slightly so
pin can reach mounting bracket.
e
.
Lock clip onto hydraulic pin.
Repeat Steps d and e on
right side.
b
.
Mount left hydraulic to left swing arm using
(1) spring, (1) M12 washer, (2) rubber pads,
(1) M12 washer (1) M8 washer, (1) nut, and
(1) nut cap.
Note: the bottom of
the hydraulic must
have the pin facing
the swing arm.
c
.
Mount right hydraulic
to right swing arm using
(1) spring,
(1) M12 washer,
(2) rubber pads,
(1) M12 washer,
(1) M8 washer,
(1) nut and
(1) nut cap.
Note: the bottom of
the hydraulic must
have the pin facing
the swing arm.
left
swing
arm
inside
of unit
outside
of unit
foot
platform
spring
nut
nut
cap
pin
washer
(M12)
washer
(M8)
rubber
pad
washer (M12)
clip
pin
foot
platform tube
mounting bracket
L
Repeat on right side.
