background image

 

 

 

LAB1283R, Issue 2, Apr 2017

 

 

 

Page 2 

 

 

 

 

 

Warnings & Safety Information 

 

IMPORTANT! PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE 

COMMENCING INSTALLATION 

 

1. Do not install this appliance in areas where the following may be present or occur: 

 

  Pollution degree 3 or 4 (as defined in EN 60335-1) 

  Excessive oil or a grease laden atmosphere 

  Corrosive or flammable gases, liquids or vapours 

  Be subject to direct water spray  

  Ambient temperatures higher than 50ºC and lower than -25ºC 

  Possible obstructions that may hinder access or removal of the unit 

 

2. This fan can be used by children aged from 8 years and above and persons with reduced 

physical, sensory or mental capabilities or lack of experience and knowledge if they have been 

given supervision or instruction concerning use of the appliance in a safe way and understand 

the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance 

shall not be made by children without supervision. 

 

3. All wiring must be in accordance with the current IEE Wiring Regulations BS7671. The 

electrical installation should be inspected and tested by a suitably qualified person after 

completion. 

 

4. The appliance should be provided with a local double pole fused spur fitted with a 3Amp fuse 

and a minimum contact separation of at least 3mm. 

 

5. Ensure that the mains supply (Voltage and Frequency) complies with the rating label. 

 

6. This appliance must be earthed. 

 

7. When installing the appliance, care should be taken not to damage any hidden utilities. 

 

8. The installer is responsible for the installation and electrical connection of the HRX2D system 

on site. It is the responsibility of the installer to ensure that the equipment is safely and securely 

installed and left only when electrically and mechanically safe. 

 

9. All regulations and requirements must be strictly followed to prevent hazards to life and 

property, both during and after installation and any subsequent servicing or maintenance. 

 

All models are IPX2 rated 

 

The HRX2D unit is free from the following substances: 

 

Asbestos 

 

 

Oils containing polychlorinated biphenyl 

 

 

Aluminum wires

 

 

Components containing mercury

 

 

Wood, cotton, silk, ordinary paper, hygroscopic material etc is not used, 

unless impregnated

 

V E N T I L A T I O N

Summary of Contents for HRX2D

















Reviews: