manualshive.com logo in svg

Dominator GDO-7v2, Installation Instructions Manual

Share
Download
Dominator GDO-7v2 Installation Instructions Manual Download Page 2

2

GDO-7v2 

Owner Installation Instructions

WARNING: 

It is vital for the safety of persons to follow all 

instructions. Failure to comply with the installation instructions 
and the safety warnings may result in serious personal injury 
and/or property and remote control opener damage. Please 
save these instructions for future reference.

Dominator® Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or 
warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an Dominator® 
Australia Pty Ltd Garage Door Opener. Dominator® Australia Pty Ltd hereby further expressly excludes all or any liability for 
any injury, damage, cost, expense or claim whatsoever suffered by any person as a result whether directly or indirectly from 
failure to install the Dominator® Australia Pty Ltd Garage Door Opener in accordance with these installation instructions. 

Summary of Contents for GDO-7v2

































Reviews:

No comments

Brands by name

Popular brands

Load more brands