background image

9

13. Changing the feet

Should you wish to install your miniCool, you will not

need the 40-mm feet. After having removed the 40-

mm  feet,  you  can  then  re-attach  the  12-mm  feet,

located inside the 40-mm feet, to the front and rear

fixing  points.  The  40-mm  feet  and  the  4  remaining

screws should be retained for future use.

14. Customer service

Before  you  call  a  service  engineer,  carry  out  the

following simple tests:

Is there a power failure? Check the fuses.
Is the plug firmly connected to the socket and is the

socket switched on? Check the socket by plugging

in another appliance, e.g. a table lamp.
Is the thermostat at the correct setting? (normally 3

or 4).
Has the door not been closed properly causing the

inside temperature to rise too quickly?
Is the refrigerator level?
Has the ventilation become obstructed?

If after checking all the above points, the refrigerator

is still not working satisfactorily, contact your nearest

service engineer. State the problem, model, product-

and serial-number.
(Details of the model, product- and serialnumber are

to  be  found  on  the  data  label  in  the  top  left  of  the

inside compartment.)
This  refrigerator  is  equipped  with  overheating

protection.  An  authorised  service  technician  can

check whether this has been triggered or not.
In  the  event  of  a  fault    developing,  contact  your

nearest  Service Centre-see local telephone directory.

15. Putting into operation

Technical data:

Model

EA 3100

EA 3080

EA 3140

RA 80; RH 200

RA 140

Type

MF20-60

MF20-60

MF20-60

Gross volume

31 litre

23 litre

41 litre

Mains operation

100V (AC)

100V (AC)

100V (AC)

Input

90W

90W

90W

Energy consumption

0.97 kWh/24h

0,92 kWh/24h

1.07 kWh/24h

Climate class

N

N

N

Refrigerant

245g NH

3

+ H

2

O

245g NH

3

+ H

2

O

245g NH

3

+ H

2

O

Figure 11

Summary of Contents for EA 3080













Reviews: