manualshive.com logo in svg

DOM Sigma Plus, Assembly Instructions Manual

Share
Download
DOM Sigma Plus Assembly Instructions Manual Download Page 11

Sigma Plus 

Assembly /Assembly without/with masterkey wavers 

 

9 

Preparation of assembly superstructure 

For each Sigma Plus contract you receive a sheet with tables of assembly super-
structures of the cylinders. If positions of core and body pins are not stated in the ta-
ble ex works please enter the pins in the table. 

The following shall apply: 

The 

FB body pins

 may only be assembled 

at the first five positions, maximally 2 

at each side of the cylinder.

 

FB body pins

 are assemble to the positions with the 

lowest values

. In case of su-

perstructures (master key system), the lowest value including the superstructure is 
considered. 
Only N pins are available as 

core pins

 for the lengths of 0, 1, 2, 3, and for the 

lengths 4, 5, 6, 7 only AB pins are available. There is no restriction of the positions 
for core pins. The core pins are applied at 

positions P1 – P6

 depending on their 

lengths. 

Assembly without masterkey wafers 

Body pins 

4 

5 

1 

2 

3 

5 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FB 

FB 

 

 

P1 

P2 

P3 

P4 

P5 

P6 

 

4 

5 

1 

2 

3 

5 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N 

N 

FB 

FB 

N

 

N

 

P1 

P2 

P3

 

P4

 

P5 

P6 

 

 

1.) At first the 

two

 

FB-body pins

 are inserted at 

the 

positions

 

P1 – P5

 with 

the lowest val-

ues

.  

(here: position P3=value 1 and P4=value 2) 

 
 
 
 
2.) 

N-pins

 are inserted at the 

remaining posi-

tions

.

 

Summary of Contents for Sigma Plus



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands