background image

 

 

22 

Parts List 

 

Dole Part No.                                               Description 
 
04-123 

Copeland Compressor No. 6DT1-3000-TSK-200-
30HP with fan assembly (Copeland 230/3/60, 
380/3/50, and 440/3/60 unit) 

 
04-124 

Copeland Compressor No. 6DT13000-TSE-200-30HP 
with fan assembly (Copeland 550/3/60 unit) 

 
24-104 

Copeland No. 018-0005-02 (Indeeco No. 40P6476-2) 
crankcase heater 

 
10-162 

 

 

Furnas No. 42HF35AC-D8 Contactor (230/3/60 unit) 

 
10-161 

Furnas No. 42EE35AG Contactor (380/3/50,440/3/60 
and 550/3/60) 

 
31-227 

Phillips 270-A-3/32 Orifice Oil Return Float Valve With 
Cast Chamber 

 
28-120 

 

 

Solenoid Valve Oil Return 

 
28-120-1 

 

 

Coil for 28-120 (Specify voltage) 

 
06-074 

 

 

Penn A19CAC-1 Thermostat 

 
28-122 

 

 

Pumpdown Solenoid Jackes-Evans 0B3S5 

 
06-134 

 

 

Penn P45NCB-1 Low Oil Pressure Safety Switch 

 
28-210 

Penn V46AE-1 1 1/4"  NPT Water Regulating Valve 
(for fresh water only) 

 
28-213 

Penn V46VE-1 1 1/4" NPT Water Regulating Valve 
with Bronze and Monel body (for seawater cooling 
only) 

 
28-114 

 

 

Jackes-Evans #J10 Water Solenoid Valve 

 
28-114-1 

 

 

Coil for 28-114 (specify voltage) 

 
06-020 

 

 

Square-D 9012-CPO-3 Pressure Switch 

 
 
 
 

Summary of Contents for FREZE-CEL 5549

























Reviews: