background image

How The DogWatch System Works

The boundary wire creates the perimeter for the DogWatch Hidden Fence System, and
can enclose any area up to 200 acres. It is buried at least 3 - 4” beneath the surface of
the yard or can lie on top of the ground (e.g.: in wooded or rocky areas). It can also be
installed around gardens or swimming pools, or attached to an existing fence to prevent
your dog from digging under or jumping over it.

Boundary Wire: 

The boundary wire carries the coded radio signal around the perimeter of

your property. It is rated for underground burial.

Signal Field:

The radio signal is transmitted from the boundary wire in all directions. It can

be used to keep dogs in or out of an area. The signal is adjusted by the 

Range

control on

the Transmitter to create a signal field on each side of the wire. Your Dealer has installed
the wire to the recommended width of 8-10 feet and has carefully configured the corners to
avoid sharp angles. 

Continuous Loop:

In order for the system to work properly, the boundary wire must

form a continuous loop. Any break in the wire will cancel the signal field. If the bound-
ary wire is broken or unplugged, the green 

Loop Monitor Display

(LMD) light will go

out and an audible warning will sound. Most breaks are caused by lawn/garden equip-
ment. If you cannot visibly locate the break, contact your Authorized Dealer for serv-
ice.

Surge Protector:

For maximum protection against power surges, DogWatch offers

both internal an external surge protection. It is important that the surge protector be
properly grounded.

This part of the system protects the transmitter from damage due

to lightning power surges. Your Dealer has attached it to the existing electrical source
house ground or a grounding rod and then connected it to the twisted wire between the
transmitter and the boundary wire.

After a lightning storm, check to be sure your transmitter is working properly. 
Do not let your dog outside until you know the system is operating.

.................................

.................................

9

Twisted Wire

Transmitter

& Surge

Protector

Boundary Wire

Signal Field

Garden Loop

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Hidden Fence System















Reviews: