Dodge Grand Caravan 2018 Owner'S Manual Download Page 200 | Manualshive

Page: 200 / 500

background image

WARNING!

(Continued)

collisions, air bags won’t deploy at all. Always wear
your seat belts even though you have air bags.

Front Air Bag Operation

Front Air Bags are designed to provide additional protec-
tion by supplementing the seat belts. Front air bags are not
expected to reduce the risk of injury in rear, side, or
rollover collisions. The front air bags will not deploy in all
frontal collisions, including some that may produce sub-
stantial vehicle damage — for example, some pole colli-
sions, truck underrides, and angle offset collisions.

On the other hand, depending on the type and location of
impact, front air bags may deploy in crashes with little
vehicle front-end damage but that produce a severe initial
deceleration.

Because air bag sensors measure vehicle deceleration over
time, vehicle speed and damage by themselves are not
good indicators of whether or not an air bag should have
deployed.

Seat belts are necessary for your protection in all collisions,
and also are needed to help keep you in position, away
from an inflating air bag.

When the ORC detects a collision requiring the front air
bags, it signals the inflator units. A large quantity of
non-toxic gas is generated to inflate the front air bags.

The steering wheel hub trim cover and the upper passen-
ger side of the instrument panel separate and fold out of
the way as the air bags inflate to their full size. The front air
bags fully inflate in less time than it takes to blink your
eyes. The front air bags then quickly deflate while helping
to restrain the driver and front passenger.

Knee Impact Bolsters

The Knee Impact Bolsters help protect the knees of the
driver and front passenger, and position the front occu-
pants for improved interaction with the front air bags.

WARNING!

•

Do not drill, cut, or tamper with the knee impact
bolsters in any way.

•

Do not mount any accessories to the knee impact
bolsters such as alarm lights, stereos, citizen band
radios, etc.

198

SAFETY

«
...
198
199
200
201
202
...
»

Summary of Contents for Grand Caravan 2018





















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Grand Caravan 2018

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

Brand: Condor Pages: 2

Brand: Motoalliance Pages: 8

Brand: StowAway 2 Pages: 2

Brand: Tachosys Pages: 28

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: Radical Sportscars Pages: 44

Brand: Volvo Pages: 42

Brand: Porsche Pages: 127

Brand: Prime Design Pages: 12

Brand: Motoalliance Pages: 4

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands