manualshive.com logo in svg

Dodge 2012 Charger, Owner'S Manual

The Dodge 2012 Charger Owner's Manual is a comprehensive guide packed with essential information to help you get the most out of your vehicle. Download the manual for free from manualshive.com and ensure you have all the necessary instructions and tips to maintain and operate your Dodge Charger efficiently.

Share
Download
background image

Clearing A Flooded Engine
(Using ENGINE START/STOP Button)

If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather

⬙

proce-

dures, it may be flooded. To clear any excess fuel, press
and hold the brake pedal, push the accelerator pedal all
the way to the floor and hold it, then press and release the
ENGINE START/STOP button once. The starter motor
will engage automatically, run for 10 seconds, and then
disengage. Once this occurs, release the accelerator pedal
and the brake pedal, wait 10 to 15 seconds, then repeat
the “Normal Starting” procedure.

After Starting

The idle speed is controlled automatically and it will
decrease as the engine warms up.

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.

The engine block heater cord is routed under the hood on
the driver side of the vehicle. It has a removable cap that
is located on the driver side of the Integrated Power
Module.

The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.

WARNING!

Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution.

368

STARTING AND OPERATING

Summary of Contents for 2012 Charger



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Charger

AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Brand: DANA Pages: 42
dallara F305 Manual preview
F305
Brand: dallara Pages: 37
Yakima BOA Installation Instructions Manual preview
BOA
Brand: Yakima Pages: 8
Yakima K343 Manual preview
K343
Brand: Yakima Pages: 11
Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Brand: Yakima Pages: 8
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Brand: Saleen Pages: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Brand: Buick Pages: 5
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Brand: Monacor Pages: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Brand: Jeep Pages: 338
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Brand: Haibang Pages: 6
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Brand: FAAFTECH Pages: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Brand: AutoMaxi Pages: 2
Thule Kit 2161 Fitting Instructions preview
Kit 2161
Brand: Thule Pages: 2
Power Acoustik METER 4 Installation preview
METER 4
Brand: Power Acoustik Pages: 4
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Brand: Demco Pages: 4
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14

Brands by name

Popular brands

Load more brands