background image

8

SR835 Crossover

DOD WARRANTY

1. The warranty registration card must be mailed within ten days after pur-
chase date to validate this warranty.

2. DOD warrants this product, when used solely within the U.S., to be free
from defects in material and workmanship under normal use and service.

3. DOD Electronics liability under this warranty is limited to repairing or
replacing defective materials that show evidence of defect, provided the prod-
uct is returned through the original dealer, where all parts and labor will be
covered up to a period of three (3) years. The company shall not be respon-
sible for any consequential damage as a result of the products use in any cir-
cuit or assembly.

4. Proof of date of purchase is considered to be the burden of the consumer.

5. DOD reserves the right to make changes in design or make improvements
upon this product without incurring any obligation to install the same on
PRODUCTS PREVIOUSLY MANUFACTURED.

6. The foregoing is in lieu of all other warranties, either expressed or implied,
and DOD neither assumes nor authorizes any person to assume for it any
obligation or liability in connection with the sale of this product. In no event
shall DOD or its dealers be liable for special or consequential damages or
from any delay in the performance of this warranty due to causes beyond
their control.

Summary of Contents for SR835













Reviews: