DockCraft The DockSider 400 Series Assembly, Installation And Operating Instructions Download Page 5

Page: 5 / 11

Assembly Instructions

–

continued

Insert Clevis Pins to set height of rack from water

–

continued

Waterside Rack

Thread Webbing through Cam Buckle :

8 - Obtain one of the Cam Buckles and Depress Lever

9 - Thread Webbing through opening in the Cam Buckle

Ensure the Single Bar on the Web Keeper is positioned as shown.

Facing up and the webbing is not twisted.

9 - Pull webbing through the Cam Buckle until the pre-marked line is in position with the cam buckle.

10 - Repeat Steps 6 - 8 to thread the webbing through the other Cam Buckle

Steps 8 - 10

Pre-marked line

Page 5 of 11

Handle

Cam
Buckle

Handle

Cam
Buckle

Handle

Cam
Buckle

Handle

Cam
Buckle

Cam Buckle
Lever upward

Circular

Retaining Ring

Hole 4

Hole 2

Clevis Pin

Head

Circular

Retaining Ring

Hole 4

Hole 2

Hole 4

Hole 2

Clevis Pin

Head

Slide

Summary of Contents for The DockSider 400 Series












Search results

Summary of Contents for The DockSider 400 Series

Reviews:

Related manuals for The DockSider 400 Series

Brands by name

Popular brands

DockCraft The DockSider 400 Series, Assembly, Installation And Operating Instructions

Search results

Summary of Contents for The DockSider 400 Series

Reviews:

Related manuals for The DockSider 400 Series

Brands by name

Popular brands