DockCraft DockSider DS200 Assembly, Installation, Setup, And Operating Instruction Download Page 5

Page: 5 / 13

Insert Clevis Pins to set height of rack from water

- continued

Waterside Rack

Thread Webbing through Cam Buckle :

–

Obtain one of the Cam Buckles and Depress Lever

–

Thread Webbing through opening in the Cam Buckle

Ensure the Slide on the Web Keeper is positioned as shown.

Facing up and the webbing is not twisted.

–

Pull webbing through the Cam Buckle until the pre-marked line is in position with the cam buckle.

–

Repeat Steps 6

–

8 to thread the webbing through the other Cam Buckle.

Steps 8 - 11

Page 5 of 13

Circular

Retaining Ring

Hole 4

Hole 2

Clevis Pin

Head

Clevis Pin

Head

Circular

Retaining Ring

Handle

Cam
Buckle

Webbing

Cam Buckle
Lever upward

Slide

Summary of Contents for DockSider DS200














Search results

Summary of Contents for DockSider DS200

Reviews:

Related manuals for DockSider DS200

Brands by name

Popular brands

DockCraft DockSider DS200, Assembly, Installation, Setup, And Operating Instruction

Search results

Summary of Contents for DockSider DS200

Reviews:

Related manuals for DockSider DS200

Brands by name

Popular brands