DMP Electronics 7133 Installation Manual Download

Page: 9 / 40

USE THE KEYPAD FOR ACCESS CONTROL

Card Readers

When a proximity credential is presented to an internal or external reader, a beep

tone is heard and the Power/Armed LEDs blink. This provides an audible and visual

acknowledgment of the credential read.

Internal Access Control Reader

The 7063/A, 7073/A, 7163, and 7173 keypads provide a built-in proximity card

reader that is compatible with most standard 125Khz Prox credentials available

from DMP and HID (1300 Series). DMP Keypads are not compatible with iClass

or other non-HID credentials. There are custom and non-standard credentials

from HID that are not compatible with DMP proximity keypads. If you are using

HID cards that have not been purchased directly from DMP, it is recommended to

thoroughly test the application fully before installation. DMP does not guarantee

compatibility with credentials not purchased from DMP. For listed access control

applications, the keypad must be installed within the protected area.

External Access Control Reader

To accept Wiegand data input from other external card readers, connect a 12VDC

external reader to the 7073/A and 7173 keypad. Connect the red and black power

wires from the reader to the power wires from the panel. These connect in parallel

with the keypad power wires. Connect the Reader (Data 1) wire to the white wire

on the 5–wire keypad harness. Connect the Reader (Data 0) wire to the green/

white wire on the 5–wire keypad harness. See Figure 4.

1K EOL

Green/White

– Connect Reader Data 0

White

– Connect Reader Data 1

Orange

– Door Strike N/O

Gray

–

Door Strike C

Violet

–

Door Strike N/C

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red
Brown/White

White/Brown

Black

– Ground

Green

– Receive Data

Yellow

– Send Data

Red

– Keypad Power

– Zone 4

– Zone 3

– Zone 2

– Zone 1

ExternalReader/Door Strike

7073/7073A, 7173 Keypads

All Keypads

Zones 1-4

7070/7070A, 7073/7073A, 7170/7173 Keypads

Surface and Backbox

Mounting Holes

Combined 4-square

and 3-gang switch box

Mounting Holes

Surface and Backbox

Mounting Holes

*All zones are supervised and suitable for fire applications.

*Maximum zone line impedence is 100 Ohms.

*Ground fault detected at 1420 Ohms or less.

Summary of Contents for 7133









































Search results

Summary of Contents for 7133

Reviews:

Related manuals for 7133

Brands by name

Popular brands

DMP Electronics 7133, Installation Manual

Search results

Summary of Contents for 7133

Reviews:

Related manuals for 7133

Brands by name

Popular brands