MPI
Connection
symbols
Lift car alarm button
DMG multiplepurpose position indicator/inductive ring
Slave
Devices :
Shaft = Shaft • Floor = Main Floor
Car TOP = Top of car • Car BOTTOM = Car bottom
Machine Room = Machine Room autodialler
Car slave device = Car slave device
2.6 - Advanced connections (EN 81-28 norm)
Signals related to the events “car in unlocking position with cabin and landing door open” and “car
running” when available from controller (or from any other device in the installation) can be used to
filter undue alarms (§ 4.2.1 in EN 81-28 norm). For this purpose, connect t
Full compliance to EN81-28 norm shall be achieved by connecting AMIGO Telephone to an external
Rescue Service (Call Center or the like) which shall manage and record the following operating tests
of the Alarm System:
2.6.1 - Cyclical operating test (§ 4.2.1 in EN 81-28 norm)
The Alarm System shall simulate an alarm event and establish a communication with the Rescue
Service at least every 72 hours (3 days). AMIGO Emergency Telephone allows this feature through
input N.6 (CYCLICAL TEST). If this input is closed (bridged), an automatic service call with the
message (”Regular Operation”) is passed every 72 hours.
2.6.2 - Emergency power supply test (§ 4.1.3 in EN 81-28 norm)
No alarm shall be lost even in case of power failure. If the Alarm System has a rechargeable battery, an
alert message shall be sent when capacity is lower than what needed to provide 1 hour of normal
operation to the system in case of power failure.
To comply with this requirement, the external Battery Charger ETS8128CH (optional) must be added
to AMIGO Emergency Telephone. Output n.5 of the charger must be connected to input n.5 (LOW
BATTERY CHARGE) of the Emergency Telephone.
When the contact is activated, AMIGO Emergency Telephone sends a service call with the “Low
battery charge” message. When the contact reopens, a service call with the “Regular operation”
message is sent.
NOTA: Battery Charger ETS8128CH checks battery status every 24 hours only with power supply. In
case of black out the low battery output is not activated to avoid the risk that service calls further affect
the battery charge.
he potential-free contact to
the ALARM FILTER input of the Emergency Telephone.
18
15
3.4 - Stand by
NEXT-WRITE-OK-ESC
Stand by menu appears on system startup and upon exit from programming mode. It shows the
software release stored in the Emergency Telephone.
Press
keys and press
"1 2 3 4"
and then "
OK
" to enter programming mode.
3.5 - Numbers from 1 to 6
1st number” to “6th number”)
If
OK
is not pressed within 30 seconds, the new number is cancelled and
the system goes back to Stand by).
The phone number contained in the chosen slot is shown on the bottom left side of the display. Press
WRITE
to modify it (if no number is present, the display shows “none”).
The “1st number” must always be present, otherwise the alarm cycle cannot start (if no “1st number” is
entered, "no tel num" will be showed in the top right side of the Stand by screen).
simulate the “Regular operation” service call. Press “
2
” to forward the call and “
*
” to close it.
This menu enables users to store the phone numbers to be called during the alarm cycle (up to 6
numbers can be stored) .
To enter/modify a phone number, scroll the menu with the
NEXT
key until the desired position is
reached (slots from “
, press the
WRITE
key, type in the phone number
and then press
OK
to save it (
From each slot it is possible to:
- manually connect to the phone line to check its availability. Press “
1
”
to connect to the line and “
0
” to
disconnect;
-
Xxx number
Next phone number
Xxx number
(MAX di 16 digits)
ESC
NEXT
WRITE
DMG
Amigo XX vX.X
Stand by
DMG
Amigo XX vX.X
stops the service call
close the phone line (if open)
14
connects to the phone line
1
0
*
2
simulate the service call “Regular operation”
to store
OK
ESC
NEXT
Next phone number
Stand by
DMG
Amigo XX vX.X
AMIGO
Emergency telephone
ETS8128CH
Alim 230Vac
1 (power + 12V)
2 (power - 12V)
5 (insufficient charge)
Fusibile rete
charger status LED
Internal battery contact
LE
D
BA
TT
ER
Y
Li
g
h
t
O
F
F
S
lo
w
b
li
n
k
in
g
N
o
rm
a
l
b
li
n
k
in
g
F
a
st
b
li
n
k
in
g
Li
g
h
t
O
N
In
su
ff
ic
ie
n
t
b
a
tt
er
y
ch
a
rg
e
or
b
a
tt
er
y
n
ot
c
on
n
ec
te
d
5
N
o
po
w
er
s
up
pl
y
an
d
B
AT
TE
R
Y
O
K
S
ta
n
d
a
rd
c
h
a
rg
e
F
a
st
c
h
a
rg
e
N
o
p
o
w
e
r
su
p
p
ly
a
n
d
B
A
TT
E
R
Y
n
o
t
ch
a
rg
e
d
2
3
0
V
A
C
1
2
V
D
C
1
2
5
B
at
te
ry
c
ha
rg
er
ET
S8
12
8C
H
Power supply
230Vac
Output
12Vdc 300mA isolated through transformer
Battery
12V 250mAh NiMh
Autonomy
stand-by 15H / conversation 2H
“Insufficient charge” ouptut
open collector max 20mA
Battery test
every 24 hours
Power connections
screw terminals 2P 5mm
Output connections
3P 5mm
Power input protection
0,5 A 5x20mm fuse
12v out
1A fuse self repairing
screw terminals
put protection
AMIGO
Emergency telephone
