Power
Mode &
BPS cap
Programming
Lock
Vision™
Status
Software
Version
Battery
Level
Max ROF
DEGASSING
- After use, remove the hopper and paintballs,then turn off your Luxe
®
X, secure the barrel blocker in place and
turn off the ASA by swinging the ASA charging handle to its extended position. This will relieve air pressure between the ASA
and vertical regulator, but, the Luxe
®
Power Core will still be charged with air. Relieve the internal pressure by pressing the bot-
tom back of the quick-strip latch at the back of your marker. This will degas your Luxe
®
X and sound similar to opening a can of
soda. Do not attempt to degas your Luxe
®
X while the ASA charging handle is in the charged position, as the continuous rush of
gas will unseat an o-ring in the Luxe
®
X quick-strip system causing a leak.
WARNING!
– If the Luxe
®
Power Core is pulled out of the body before it is fully de-gassed it may be under enough pressure to
fire a single low-power shot as it is being removed. Always turn off and or remove the gas supply (see the Luxe
®
X manual or quick-
start) and hold the quick-strip latch open until no escaping gas can be heard, before pulling back to extract the power core.
{FIG. 06}
-
CLEANING
- The Luxe
®
power core can be removed for cleaning or inspection by gripping the top of the quick-strip latch and
pulling the entire assembly out the back of the marker. The bolt serves as the marker’s exhaust valve and is the main moving
part. Unscrew the fire chamber from the quick-strip mechanism and the bolt may be removed from between the two compo-
nents. Clean the parts of the power core and replace any o-rings showing signs of damage or severe wear. Lightly lubricate the
contact surfaces of all o-rings with Luxe
®
GR33SE
TM
. Non-approved lubricants may cause damage and void your warranty. Do
not use oil. This simple cleaning, and the Detent/Vision
®
cleaning mentioned below is the only routine maintenance required to
properly care for your Luxe
®
X.
PROGRAMMING
– The The Luxe
®
X OLED display and exclusive Luxe
®
voice feedback make it easy to navigate your marker’s soft-
ware menus. Unlock the marker and turn it on while holding back the trigger to open the Main Menu. Pull the trigger to scroll through the
available settings. To make a change, find the desired setting and tap the power button. The Luxe
®
will display the currently selected value
for that sub-menu on its OLED display with “SET” appearing on screen. Changes may be made by pulling the trigger to cycle through the
available values. Tapping the power button will select a value and return to the main menu. Press the power button for approximately 2
seconds to turn off the Luxe
®
and exit programming mode.
POWER
– Turn on your Luxe
®
X by double-clicking the power button or
pressing and holding it for two seconds. When the Luxe
®
is on, the Luxe
®
X
display will be illuminated to show its status.
{FIG. 03}
WARNING!
– Turn-
ing off your Luxe
®
X is the equivalent of setting the safety on a mechanical
paintball marker, but should not be relied on in place of a barrel blocking
device and paintball goggles.
Your Luxe
®
X will turn off automatically if it sits
idle for one hour.
VISION
– The Vision
®
anti-chop system is on by default. It may be turned
off or back on with a quick double-tap of the button. Vision
®
status will be
indicated in the Luxe
®
X display with a solid circle when a paintball is de-
tected in the breech, or an empty circle when the Vision
®
beam is unbroken.
Vision
®
Fault indicates that the beam has not cleared after firing, usually due
to debris blocking an eye.
TOURNAMENT LOCK
– The Luxe
®
X tournament lock switch makes t
he programming menu unavailable when it is turned on. To change the lock
setting, open the left side of the rubber grip and slide the tournament lock
switch (located next to the USB-C charging port) towards the barrel to un-
lock, or towards the back of the marker to lock. The lock status is displayed
on the OLED screen with an open or locked padlock. Some events may
require the rubber grip to be secured with screws in place of snap posts, so
that the lock may not be accessed without using a tool.
BARREL/REGULATOR GRIP PANEL
- Assemble the Included Freak
®
XL Barrel and install it on your Luxe
®
X. The interchangeable grip panel on the
vertical regulator can be changed by removing the regulator nut on the
bottom of the vertical regulator with a 5/16-inch
hex-key.
BARREL BLOCKER
-
The barrel blocker is an important safety device
and should be used any time the Luxe
®
X is connected to an air supply or
turned on unless all persons within range are protected by paintball goggles
and or netting. Slide the barrel blocker over the end of the barrel cinch
down the cords over the rear of the marker to secure it in place.
AIR SETUP
- Your Luxe
®
X is a high-performance paintball marker. Pres-
sure spikes from liquid CO
2
can cause internal damage and will void the
Luxe
®
warranty. Use only regulated compressed air as a power source. HPA
systems set for 450-550 psi output are ideal. Low-output 250psi systems
may be used with your Luxe
®
X but may cause velocity drop-off at high
rates of fire. With the barrel blocker in place, screw a filled paintball
compressed air system into the Luxe
®
ASA. Charge your Luxe
®
X with
air by rotating the ASA charging handle to the rear position.
{FIG.04}
WARNING!
– Once your Luxe
®
X has been charged with air, it can hold
enough air to fire 2 or more shots, even after the HPA system has been
removed.
VELOCITY ADJUSTMENT
- Velocity must be tested and adjusted at
the start of each paintball session. Attach a hopper and filled HPA system to
your Luxe
®
X. Fill the hopper with fresh 68-caliber paintballs. While wearing
paintball goggles, while everyone in range is similarly protected, remove the
barrel blocking device, rotate the ASA charging handle to charge your Luxe
®
X with air, turn on the power and take a few test shots over a chronograph.
Adjust the velocity of your Luxe
®
X with a 5/32-inch hex key inserted in
the bottom of the marker’s vertical regulator. Turn clockwise (like tighten-
ing a screw) to increase velocity and counter-clockwise (like loosening) to
decrease. After each adjustment take a few shots, then re-adjust as needed
until the desired velocity is reached. Never adjust your Luxe
®
X to fire at
velocities greater than 300 feet per second (91.4 m/s).
{FIG. 05}
FIG. 2
FIG. 2
AIR ON
u
u
03
POWER
AIR SETUP
VELOCITY ADJUSTMENT
+
–
AIR OFF
05
2}
PUSH IN with thumb
3}
LIFT UP
04
ELECTRONIC ADJUSTMENTS
06
DEGASSING
IMPORTANT!
Degas by lifting Tail Cover
until fully degassed.
1}
Degas ASA
by rotating lever
u
u
SETUP & OPERATION
SETUP & OPERATION
u
u
