manualshive.com logo in svg

DLP Design USB-Parallel FIFO Module DLP-USB245R, User Manual, Page: 11 / 13

Share
Download
DLP Design USB-Parallel FIFO Module DLP-USB245R User Manual Download Page 11

Rev. 1.0 (November 2008)                                           11                                              © DLP Design, Inc.

 

 

10.0  MECHANICAL DRAWINGS  (PRELIMINARY) INCHES 
(MILLIMETERS) UNLESS OTHERWISE NOTED 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 

 
 

11.0  DISCLAIMER

 

 

© DLP Design, Inc., 2008  
 
Neither the whole nor any part of the information contained herein nor the product described in 
this manual may be adapted or reproduced in any material or electronic form without the prior 
written consent of the copyright holder. 
 
This product and its documentation are supplied on an as-is basis, and no warranty as to their 
suitability for any particular purpose is either made or implied.  DLP Design, Inc. will not accept 
any claim for damages whatsoever arising as a result of the use or failure of this product. Your 
statutory rights are not affected.  This product or any variant of it is not intended for use in any 
medical appliance, device or system in which the failure of the product might reasonably be 
expected to result in personal injury. 

0.23 typ

(5.8 typ)

0.21 typ

(5.3 typ)

Side View

0.37 typ

(9.4 typ)

0.60 typ

(15.2 typ)

0.22 typ

(5.6 typ)

1.26 typ

(32.1 typ)

0.43 typ

(10.9 typ)

0.09 typ

(2.3 typ)

Summary of Contents for USB-Parallel FIFO Module DLP-USB245R














Reviews:

No comments