background image

7. 

LED Status Indicators 

 

The Model 1000 has 12 LED indicators to show the status of the inverter, batteries and to assist in 
troubleshooting. 

 

 

LED Description 

UTIL OPER 

GREEN LED indicating that the 115 VAC power output at J2 is sourced from the utility 
company and the inverter is in stand-by mode. 

INV ON 

YELLOW LED indicating that primary (utility company) power is unavailable and the 115 
VAC power at J2 is being sourced from the inverter. 

B BAD 

RED LED blinks when the battery has been tested to be low, comes on steady when battery 
is bad. 

B OK 

GREEN LED indicates that the battery has been tested and is good. 

BULK 

YELLOW LED indicates that the battery is being bulk charged; blinking indicates that the 
battery is at 90% of full charge. 

TRICK 

GREEN LED indicates that the battery is fully charged and the system is applying a trickle 
charge to it to maintain the full charge. 

TEMP 

RED LED indicates that the battery is not being charged because the temperature is outside 
the battery safe operating range: 23°F (-4°C) to 126°F (52°C). 

SHDN 

RED LED located in the upper left of the circuit board.  This LED is ON when the system has 
shut down the inverter because of low battery voltage. 

110V ON 

RED LED (2) indicates that 115 VAC is present at the power output terminal (J2). 

DIAGNOSTIC 

GREEN LED indicates the status of the charge state.  Used by DK technicians for 
troubleshooting. 

HRT BEAT 

GREEN LED blinking indicates that the microprocessor is operating. 

 

 

 

8. 

Test / Reset Buttons 

 

BATT TEST 

Pressing the BATT TEST push button will initiate a quick test of the battery and its charge state.  
The test takes 20-30 seconds to complete.  When the BATT TEST button is pressed, the B OK 
led will turn off.  When the test is complete, the B OK led will turn on. 

 

RESET 

Pressing the RESET push button will reset the circuit board to its start-up state. 

Page 12 

 

1000-065-B-7-09 

Summary of Contents for 1000-080


















Reviews: