©
2018 DJI All Rights Reserved.
43
Remote Controller
5HPRWH&RQWUROOHU3URÀOH
The Cendence
TM
remote controller features DJI’s Lightbridge technology for a maximum transmission
distance of up to 4.3 mi (7 km).* Equipped with a DJI CrystalSky
TM
7.85 inch monitor, which offers an HD
MJWFDBNFSBWJFXXJUIJUTC*1JMP*(05.BQQGPSBQSFDJTFBOESFTQPOTJWFnZJOH
experience. Dual transmission frequency support makes HD video downlink stable and reliable. In Dual
Remote Controller mode, two remote controllers can control the aircraft and camera separately and
simultaneously. Dual Remote Controller mode even works when users are up to 328 ft (100 m) apart.
The remote controller works with a WB37 intelligent battery, which can be charged via the charging
port (in about 2 hours and 24 minutes with a 180W charger) or with the WCH2 Intelligent Battery
Charging Hub (in about 1 hour and 11 minutes). The maximum operation time of the remote controller
is approximately four hours without supplying power to a monitor and with the Dual Remote Controller
mode disabled.*
8JUIWBSJPVTDVTUPNJ[BCMFCVUUPOTZPVDBOBEKVTUBOVNCFSPGnJHIUDPOUSPMMFSDBNFSBBOEHJNCBM
parameters with just your hands. The Cendence Patch Antenna also allows for high-gain signal
transmission and improved reception.
* The remote controller can reach its maximum transmission distance (FCC) in a wide open area with no
electro-magnetic interference at an altitude of about 400 feet (120 meters).
To comply with local regulations, the 5.8 GHz frequency is not available in some countries and regions.
Maximum run time is estimated without supplying power to a smart device or monitor.
Compliance Standards:
The remote controller is compliant with local laws and regulations.
Stick Mode:
Controls can be set to Mode 1, Mode 2, or to a custom mode.
Mode 1:
The right stick serves as the throttle.
Mode 2:
The left stick serves as the throttle.
Please refer to the CrystalSky User Guide for more CrystalSky details.
Do not operate more than three aircraft within the same area (roughly the size of a soccer
mFMEUPQSFWFOUUSBOTNJTTJPOJOUFSGFSFODF
Preparing the Remote Controller
Mounting/Removing the Intelligent Battery
Put the battery into the Battery Slot, then slide it to the end until you hear a click.
OK
Press the Battery Release Button before removing the battery.
Press the Battery Level Button once to check the battery level.
Charging the Battery
The remote controller is powered by a WB37 intelligent battery, which can be charged via the
charging port or by the WCH2 Intelligent Battery Charging Hub.
Summary of Contents for MATRICE 200 series
