dIXEL
Operating Instructions
cod. 1592017410
1592017410 XLH360 GB r1.0 15.04.2005.doc
XLH360
5/16
7.
MATURING CYCLE WITH DRIPPING, RUNNING AND STOPPING PHASE.
Dripping
Running
Stopping
Running
Stopping
The diagrams displays a typical maturing cycle with the starting dripping phase.
DRIPPING PHASE
lasts for the “
dri
” time, without humidity control, temperature set is SETG
RUNNING PHASE
lasts for the
“on”
time, both temperature and humidity are controlled.
STOPPING PHASE
lasts for the
“off”
time, without any control of temperature and humidity.
The end of the stopping phase is signalled by the internal buzzer and by the “End” message on the display.
After
the
STOPPING PHASE
the behaviour of the controller depends on the parameter
trc,
according to the following settings:
trc
=
co
controller maintains the set points of the running phase
trc
=
in
controller stop the regulation at all.
trc
=
cL
controller performs the running and stopping phase till is stopped manually.
trc
=
cLE
as (
trc
=
cL
) plus at the end of each cycle the
End
label is displayed and the buzzer is switched on.
7.1
HOW TO SET THE DURATION OF THE DRIPPING, RUNNING AND STOPPING PHASES
1.
Push the
CLOCK
key, the display shows on the bottom display the “dri” message, while the “hourglass” start flashing.
2.
Push again the
CLOCK
the duration of the dipping phase is shown, hh:mm.
3.
To set the duration push the
UP
and
DOWN
keys.
4.
Push again the
CLOCK
to confirm the time and pass to the setting of the running phase: the “on” message is displayed.
5.
Push the
CLOCK
key to see its duration and use the
UP
and
DOWN
keys to set it.
6.
Push again the
CLOCK
to confirm the time and pass to the setting of the stopping phase: the “oFF” message is displayed.
7.
Push the
CLOCK
key to see its duration and use the
UP
and
DOWN
keys to set it.
8.
Confirm the value by pushing again the
CLOCK
key and pass to the humidity display.
7.2
HOW TO SET THE TARGET HUMIDITY OF THE RUNNING CYCLE
1.
Push the
SET %RH
key, the display shows on the bottom display the “SH1” message, while the “set” icon starts flashing.
2.
Push again the
SET %RH
the humidity set point of the running phase is shown. Set it using the
UP
and
DOWN
keys. To
disable
the
humidity control during the freezing phase set it to “
nu
”.
3.
Push again the
SET %RH
to confirm the value and pass to the humidity display.
7.3
HOW TO SET THE TARGET TEMPERATURE OF THE DRIPPING AND RUNNING PHASES
1.
Push the
SET TEMP
key, the display shows on the upper display the “StG” message, while the “set ” icon starts flashing.
2.
Push again the
SET TEMP
the temperature set point of the
running
phase is shown. Set it using the
UP
and
DOWN
keys.
3.
Push again the
SET TEMP
to confirm the value and pass to the setting of the
dripping
phase: the “St1” message is displayed.
4.
Push the
SET TEMP
key to see its value and use the
UP
and
DOWN
keys to set it.
7.4
HOW TO START THE CYCLE
Push and release
START
key: the led
will be turned ON.
The
led flashes during the proving phase
7.5
END OF THE CYCLE
When the timer has expired, the buzzer starts sounding and the bottom display shows the “
End
” message.
To mute the buzzer push a key: The display come back to show the humidity and the LED of the START key is turned off.
7.6
HOW TO STOP THE CYCLE MANUALLY
To stop the cycle manually push the
ON/OFF
key
.
7.7
HOW TO MODIFY THE SETTING OF THE CURRENT CYCLE WHILE IT’S RUNNING
To modify the setting of the running cycle temperature (SET TEMP), humidity (SET %RH) or remaining time (CLOCK):
