manualshive.com logo in svg

Ditel MICRA-D, Instruction Manual

Share
Download
Ditel MICRA-D Instruction Manual Download Page 42

42

9.1.2 – Installation 

Lift out the electronics assembly from the case and use a screw-driver to push on 
the junctions between the case and the shadow areas to detach them from the 
case. See fig. The so performed orifice will allow any of the setpoints (2RE, 4RE, 
4OP or 4OPP) board output connectors be brought out at the rear of the 
instrument. The option is installed by plugging the connector in the main board 
location. Insert the card pin in the corresponding main board slot and push down 
to attach both connectors. 
    If the instrument is to be installed in high vibrating environments, it is 
recommended to solder the card to the main board making use of the copper 
tracks on both sides of the card pin and around the main board hole on its solder 
side. 

9.1.3 – Wiring 

2RE 

- 2 RELAYS OPTION 

PIN 4 = NO2 

PIN 1 = NO1 

PIN 5 = COMM2  PIN 2 = COMM1 
PIN 6 = NC2  

PIN 3 = NC1 

 
 

4RE 

- 4 RELAYS OPTION 

PIN 4 = RL4 

PIN 1 = RL1 

PIN 5 = N/C 

PIN 2 = RL2 

PIN 6 = COMM  PIN 3 = RL3 
 

 

4OP 

- OPTION 4 OPTOS NPN 

PIN 4 = OP4 

PIN 1 = OP1 

PIN 5 = N/C 

PIN 2 = OP2 

PIN 6 = COMM  PIN 3 = OP3 
 
 

4OPP 

– OPTION 4 OPTOS PNP 

PIN 4 = OP4 

PIN 1 = OP1 

PIN 5 = N/C 

PIN 2 = OP2 

PIN 6 = COMM  PIN 3 = OP3 

 

42

9.1.2 – Installation 

Lift out the electronics assembly from the case and use a screw-driver to push on 
the junctions between the case and the shadow areas to detach them from the 
case. See fig. The so performed orifice will allow any of the setpoints (2RE, 4RE, 
4OP or 4OPP) board output connectors be brought out at the rear of the 
instrument. The option is installed by plugging the connector in the main board 
location. Insert the card pin in the corresponding main board slot and push down 
to attach both connectors. 
    If the instrument is to be installed in high vibrating environments, it is 
recommended to solder the card to the main board making use of the copper 
tracks on both sides of the card pin and around the main board hole on its solder 
side. 

9.1.3 – Wiring 

2RE 

- 2 RELAYS OPTION 

PIN 4 = NO2 

PIN 1 = NO1 

PIN 5 = COMM2  PIN 2 = COMM1 
PIN 6 = NC2  

PIN 3 = NC1 

 
 

4RE 

- 4 RELAYS OPTION 

PIN 4 = RL4 

PIN 1 = RL1 

PIN 5 = N/C 

PIN 2 = RL2 

PIN 6 = COMM  PIN 3 = RL3 
 

 

4OP 

- OPTION 4 OPTOS NPN 

PIN 4 = OP4 

PIN 1 = OP1 

PIN 5 = N/C 

PIN 2 = OP2 

PIN 6 = COMM  PIN 3 = OP3 
 
 

4OPP 

– OPTION 4 OPTOS PNP 

PIN 4 = OP4 

PIN 1 = OP1 

PIN 5 = N/C 

PIN 2 = OP2 

PIN 6 = COMM  PIN 3 = OP3 

 

Summary of Contents for MICRA-D





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands