Ditch Witch 420sx Operator'S Manual Download Page 79

Page: 79 / 141

Drill - 78

420sx Operator’s Manual

CMW

Turning shaft will kill you or crush arm or leg. Stay away.

NOTICE:

Keep everybody at least 10’ (3 m) away from drill pipe during operation. Do not straddle

trench or drill pipe while drilling.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

NOTICE:

Set up warning barriers and keep people away from equipment and jobsite while drilling.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

Improper control function could cause death or serious injury. If control

does not work as described in instructions, stop machine and have it serviced.

NOTICE:

Do not tape or tie down switch.

Summary of Contents for 420sx














































































































































Search results

Summary of Contents for 420sx

Reviews:

Brands by name

Popular brands

Ditch Witch 420sx, Operator'S Manual

Search results

Summary of Contents for 420sx

Reviews:

Brands by name

Popular brands