manualshive.com logo in svg

Ditch Witch 420sx, Operator'S Manual

Share
Download
Ditch Witch 420sx Operator'S Manual Download Page 18

420sx Operator’s Manual

Safety - 17

Safety Alert Classifications

CMW

Safety Alert Classifications

These classifications and the icons defined on the following pages work together to alert you to situations 
which could be harmful to you, jobsite bystanders or your equipment. When you see these words and 
icons in the book or on the machine, carefully read and follow all instructions. YOUR SAFETY IS AT 
STAKE.

Watch for the three safety alert levels: 

DANGER

, 

WARNING

 and 

CAUTION

. Learn what each level 

means.

indicates an imminently hazardous situation which, if not avoided, will result in death or 

serious injury.

indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury.

indicates a potentially hazardous situation which, if not avoided, may result in minor or 

moderate injury.

Watch for two other words: 

NOTICE

 and 

IMPORTANT

.

NOTICE

 can keep you from doing something that might damage the machine or someone's property. It 

can also alert you against unsafe practices.

IMPORTANT

 can help you do a better job or make your job easier in some way.

Summary of Contents for 420sx














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands