10(33)
User manual in Original
Dok. ref: User manual 500A-BAS Rev. B
DISPERATOR AB
Tel: +46 8 724 0160
E-mail: [email protected]
Mälarvägen 9, SE-141 71 Segeltorp, Sweden Fax: +46 8 724 6070
Web page: www.disperator.se
3.2.
Technical Specification
Technical specification
510A
515A
520A
530A
550A
575A
Normal capacity, kg/hr.
300
400
500
700
850
1000
Electrical power, kW
0,75
1,1
1,5
2,2
4,0
5,5
Rated current, A for:
400V / 3 ph. / 50 Hz
2,1
2,6
3,6
5,2
8,6
11,5
440V / 3 ph. / 60 Hz
2,1
2,4
3,5
5,0
7,5
10,0
480V / 3 ph. / 60 Hz
1,9
2,6
3,5
4,6
7,2
9,6
Other 3-ph voltages available 1-ph 220-240V, 50/60Hz also available for models 510 and 515.
Control voltage
For marine installation the same as motor voltage. For land installation 230V/50Hz.
Fuse rating, slow
10A
10A
10A
16A
16A
16A
Gross / net weight, kg
29 / 25
30 / 26
34 / 31
48 / 44
51 / 47
57 / 53
Measurement a
151
151
151
176
176
176
Measurement b
460 see (3)
460 see(3)
583
560 see (4)
560 see (4)
655
Measurement c
See (3)
See (3)
583-763
560-740 see (4)
560-740 see (4)
655-835
Measurement d
40
40
40
75
75
75
Measurement e
2”
BSP,
Female
2 ½”
BSP,
Female
Measurement f
253
253
253
310
310
310
Measurement g (legs)
See (3)
See (3)
204
236
236
236
Measurement h (inlet)
160
160
160
174
174
174
Measurement k
150
150
150
175
175
175
The Disposer works in the temperature range -5°C - +40°C
(1) Installation material needed but not incl. in standard delivery are:
• main electrical safety switch,
• flexible hose R½” for cold flush water,
• backflow preventer for flush water,
• water trap for connection to disperator outlet,
• torque protection bar for fixating the disposer.
Can be ordered from DISPERATOR.
(2) For connection to start/stop unit including contactor and overload
protector (IP66) placed on wall/bulkhead. Start/stop unit to be
connected to main electrical safety switch, see (1).
(3) 3-ph unit without legs as standard. Legs available as option and then
with same measurement b, c and g as for model 520. 1-ph unit with
legs as standard and with same measurement b, c and g as for
model 520.
(4) Short version (b = 525 mm and c = 525-705 mm) and long version
(b = 655 mm and c = 655-835 mm) available as option.
(5) User manual with installation and service instructions,
wiring diagram, laminated operating instructions and
laminated safety instructions included in delivery.
d
c b
a
5°
3 x 120°
k
e
Ø207
h
f
g
Top view
Disposer outlet to be
connected to a water trap,
see (1). Slope of drain
pipe 2:100 to 5:100
Adjustable legs 3 pcs. for model 520,
530, 550 and 575. Optional for model
510 and 515, see (3)
Disposer housing,
stainless steel
EN 1.4301 (AISI304)
Motor cable outlet
and 2 m cable, see (2)
All measurements in mm
Motor IP55
(see table)
To suit drain connection disposer with
outlet can be turned and positioned in
6 x 60° intervals
Side view
Fixing holes diam. 9 mm, 6
pcs and gasket for assembly
connection. For CE-marking
an approved assembly from
DISPERATOR or other
manufacturer is needed
above disposer inlet.
Labyrinth outlet for
motor cooling air
Torque protection
bar, see (1)
Air inlet in bottom
plate for motor
cooling, min 15mm
clearance
